GTAN4250M1WS General Electric Washer - Instructions

The trick is to pull the front cover off by using a putty knife .slide it under the cover at both front corners.it will click on each corner.then pull front cover off .lift off the bottom catch hooks.look for the pump on the bottom right side.unplug the wite connector .take 2-5/16 bolts out holding the bracket.then grab a pliers .squeeze the hose clamps and pull the 2 hoses off.assemble new pump.

I notice a strange noise when ever the tub would shut down from a spin cycle. When I would load clothes it seemed that the basket had to much lateral movement. I looked between the top of the frame & basket & found 2 of the dampening straps had broken. Ordered 4 of them to replace all the straps.

Replacement was easy. I popped the front cover of the machine off. Remove 2 screws which held the top down which gave easy access to the straps. The straps are held in place by 2 screws so it was a simple process of removing the screws, removing the straps from their anchors & reinstalling the screws with the new straps. Job done. Reinstall the top & front of the machine & put the wife back to work.

Ordered lid switch from parts select via website. Two days later I received the part in the mail. Instead or re-wiring, I cut wire close to existing bad switch. Splice two wires and cap with wire nuts. Zip tie loose wire to tub housing.

watched the video, and it was simple!

Tub seal was found completely broken. Replaced it.
Then replaced tub bearing, tub bearing washer, shaft & mode shifter assembly and 6-rib drive belt.
Reassembled and tried, more quieter and like new machine.

Loosening tub nut was a challenge as it was bit corroded, use of WD40 was a great help.
Knowledge from you tube was a great help.

After unplugging the washer, I drained remaining water from washer tub using my Wet/Dry vac. Ordered new pump Sunday night from PartSelect, 'Standard delivery', part arrived Tuesday morning. Removal & installation took less than 20 minutes.

Use paint scraper to release spring tabs holding front cover on.

Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.

R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).

Super easy and super cheap!

IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.

Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.

FIRST, TURNED OFF THE MAIN VALVE INTO THE HOME..AND BLED THE LINES. USED A SMALL BUCKET AND DISCONNECTED THE LINES FROM THE WASHER. TOOK THE PLATE OFF THE WASHER AND DISCONNECTED THE OLD INLET VALVE CONNECTED THE NEW VALVE AND REPLACED THE COVER PLATE. SINCE I HAD THE MACHINE DISCONNECTED, I PUT NEW WATER LINES AND REPLACED THE HAT AND COLD WATER VALVES WITH NEW 1/4 TURN BOILER BALL VALVES. TURNED THE WATER BACK ONTO THE HOUSE AND RAN THE FAUCET SO THERE WOULD BE NO AIR IN THE LINES WHEN I TURNED THE WATER ON TO THE WASHER.

Took all apart.. front off,top off, took basket top off..took the basket assembley out by unhooking the four shocks. Took a picture of all wireing and fittings. Then came the most difficult. The main nut that holds the basket to the main shaft. If you do not have one of the wrenches made for that nut good luck. Between all the gunk and rusty parts around it. It would not budge. I used a pipe wrench and a 3# hammer and it wouldnt budge. It is a oppisite drive nut so it comes off in reverse as a regular one. I ordered the wrench on line to use on the new one i orderd. Had to because the nut was getting chewed up. So waiting to order the parts i needed i ground down the nut with my angle grinder.. worked well. Knowing i had to replace the main drive and bearing it wasnt that bad. Got the nut off... pulled the basket out and then the shot seal. Really looked tore up. So because of the seal leaking, the water drips down onto the main drive and thats what ruined it. Cleaned everything up really nice.. went to put the new seal in and noticed it didnt fit as tight as it should.. so i put some silicone around it and installed everything back together. Still thinking of the seal still i went ahead and finished it all and guess what. It leaked.. the seal in my opinion needs to fit over top of the plastic main bucket not just inside of it. After researching the same problem some guys said they filled the bearing seat with silicone and it helped. Others say the plastic tub needs replaced because the bearing seat is wore out.. the tub is like $70.00. The seal is $8.00. So, what to do? Buy another tub and seal and hope the seal fits in tight, or gob alot of silicone on the seal and older tank and see.. the washer new was like $600.00. Been dicontinued now. The main shaft assembley was $160.00... seal$8.00.. the tool for $15.00...misc stuff still comes out to $200.00 . Now to buy a new tub? Is it worth it or not.. we'll see

used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.

Removed the bolt holding the agitator coupler on, replaced it and the bolt then slid the agitator on the coupler and the fabric softener dispenser on top of that.... so easy!!

First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

R&R Leaking/Damaged Hose and replaced it with the new one. One thing to be aware of is that after removing screws from the discharge hose upon removing the damaged one there was some water that did not expel from the unit so there was about a cup of water that came out. After removing the leaking hose you will need to remove the retaining plastic piece so that it can be placed on the replacement hose. Or if you ordered one put it on the hose so that it can retain the end of the hose in the washer. The anti-siphon clip is located about half way up the back of the washer it simply clips in place.