All Installation Instructions for Amana Refrigerator GT2425PDDW

old knob broke

New knob fit right in.

Parts Used:

Cold Control Knob - Fresh Food

Ted from Eugene, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Light didnt go on

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Parts Used:

Refrigerator Door Switch

dorotea from staten island, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

part was missing

installed new part easy

Parts Used:

Hinge Washer

Lower Hinge Pin

Van from HARTFORD, WI
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

changed the light bulb still would not work so I figured it was the switch sure enough.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

Parts Used:

Refrigerator Door Switch

anthony from HAVELOCK, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Ice from icemaker taste metallic; new ice maker directly from box

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

Parts Used:

Plastic Tubing

Samuel from ALEXANDRIA, VA
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old door seal was torn

Removed screws & old seal replaced seal and screws.

Result: New seal will not lay flat against the door making it difficult to close the door completely and causing the compressor to work overtime. I am hoping that it eventually flattens out.

Parts Used:

Fresh Food Door Gasket

Robert from New City, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Refrigerator Fresh Food Gasket

I merely removed the old one and replaced the old one, I luckily had a ratcheting screw driver which made things go alot quicker as there were 36 screws holding the gasket on the inside of the door, also I had to replace some of the screws that I tightened as they stripped out in the door metal, I GOT SOME OF THE SAME DIMENTION with a slightly larger thread new screws and carefully screwed them in with no problems at all. Thank you for your professional speedy service. I will surely contact you again when I need parts for my appliances even if I m not the MAYTAG repair man.

Parts Used:

Fresh Food Door Gasket

Malcolme from Saint Petersburg, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broke light switch while cleaning

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Parts Used:

Refrigerator Door Switch

Gail from Golden, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Light switch broke

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

Parts Used:

Refrigerator Door Switch

Carolee from Spokane Valley, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The support had broken and the shelf was just hanging there.

I unscrewed the support and replaced it with one that I ordered. It was fast and easy.

Parts Used:

Crisper Drawer Shelf Support

Deanie from Amarillo, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The bottom brackets on the inner door were missing.

The frig had broken brackets on the inner door. I connected the clips to the trim piece and I snapped the entire piece into the slots on the door. Presto! All finished.

Parts Used:

Shelf Retainer Bar End Cap

Door Shelf Retainer Bar

Linda from Saginaw, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Retainer clip was broken and as a result the retaining bar could not do its job

I just snapped the new clip in place.
I would like to thank you for your fast service. The part arrived the day after I placed the order. This is almost unheard of.
Thank You

Parts Used:

Shelf Retainer Bar End Cap

WILLIAM from TAMPA, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broken hinge bearing on ice maker

Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove, 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY

Parts Used:

Water Fill Cup and Bearing

ROBERT from WESTFIELD, IN
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Ice catcher was missing from the icemaker

I removed the ice catcher from the excellent packaging, rinsed it, and placed it on the counter next to the fridge. I opened the door the the freezer and placed the ice catcher under the icemaker. I lowered the arm on the icemaker and closed the door to the freezer. Then I opened the door to fridge, took out a Guinness, popped the top, and sat down to savor my success.

Parts Used: