GSS26C5XXA02 Whirlpool Refrigerator - Instructions

Prior to ordering I removed freezer panel and checked for ice build up and fan functionality. Then removed rear panel cleaned lint from everything pulled front panel vacuumed out the condenser. Plugged back in and all seems to work with the exception of compressor. I have a little experience so googled in model number and your site popped up. I looked up part and the site gave me a percentage loved that. I ordered wish I would have rushed shipping as took about 10 days. Installed in less than 30 minutes and all runs great ??

Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.

Instructions were great five minutes to remove and replace fan....Thank You............ saved big money

I removed the filter from the box I took the old filter out and inserted the new air filter put the cover down and that was it.

I replaced the water inlet valve. This was a easy except for the place the valve was located. I removed the back panel cover after unplugging the refrigerator, shut off the water feed line to the refrigerator. After some cleaning with a vacuum cleaner, to remove build up dust and lint, I was able to reach in and pull the valve loose from the mounting bracket. I removed the electrical plugs from the valve and all three water lines. One that was completed, I was able to remove the valve from it's location. Replacing the valve, was easy enough, as I just attached the water line hoses back into the mounting location and plugged in the electrical plugs, then placed the valve back onto the mounting bracket. I then turned the water feed line back on and checked for leaks. Once I was able to make sure there were no water leaks, I replaced the back panel cover and plugged the refrigerator back it to the power plugin. The valve immediately began working, supplying water to the icemaker.

Googled "intermittent clicking noise" or something similar and consensus was it was either the capacitor or compressor start relay. You-tubed videos on how to replace these. Looked easy. Just unplug them from the condenser and replace. Contacted Part Select and staff said 50% of the the time it was the capacitor, 50% of the time it was the relay. I was in a time crunch so I ordered both and they came in a couple of days. I replaced the capacitor but the clicking noise continued. I replaced the relay and problem solved! Maybe I could have gotten away with just replacing the relay, but I had them both by then and figured with a 10 year old fridge, better replace them both at the same time and be done with the problem. So far, so good.

pulled the top shelf and poped open the door and replaced the filter

Took it out of the box. Emptied the ice out of the broken bin. Slid the new one in and all done.

As shown on the YouTube link sent with email receipt.
Removed back panel. Removed the clip securing the parts with long nose pliers. Unplugged the old, replugged the new. Replaced the clip to secure.

Unfortunately, the capacitor and relay did not fix the loud clicking issue.

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

1. Tried to unscrew the bolt that held the broken coupling.
2. Had to have daughter hold on the plastic spinner on the other side so that the bolt would unscrew and not make the whole mechanism spin.
3. Screw came out.
4. Put coupling in place.
5. Put screw back in and tightened everything up.
Really easy, once the screw actually began coming out.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I used the computer to enter the make and model of the refrigerator with the icemaker unit. We looked at the diagram to identify the name of the part and then ordered it. It was sent out the next day! We received it and installed it and it works perfect!

It was so easy. I had no idea. My husband and I were directed to your site and we ordered the part with scepticism but with hope that it would solve the problem. As soon as it came in, my husband installed it in five minutes. It was working immediately. Thank you.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!