GSK25LCNACCC General Electric Refrigerator - Instructions

Replaced both the Defrost Thermostat and Defrost Heating Element. The You Tube repair video clips were extremely helpful for both operations. My difficulty was getting access to the parts that needed to be replaced in a very tight side by side freezer space. Otherwise, the repair went smoothly and the refrigerator is back in normal operation in time to save the perishable food inside.

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

Knew the switch was bad. Researched on the internet how to fix. Used a steak knife to pop the old one out, changed the contacts to the new switch and popped it back in. It took longer to open the box than it did to replace the switch. And the part arrived 2 days after I ordered it.

looked up the part on your site which was very quick and easy. Ordered the part and it came quickly and my installation was just as quick. Greatful for your web site Regards John

I just snapped in the new side to the shelf ...very simple and easy:-)

Snapped it into place. Nothing to it!

It was so darn easy! Took less then 10 minutes to fix. Self explanatory no instructions needed! Very cool!

removed 6 screws and repaced cover.

Disconnected the refrigerator for a few hours. On back of frezer compartment unscrew 4 screw to get access to Old defrost thermostat (D. T.). I cut the two wires with pliyers atached to D. T. Peel them about one inch both the old and new D. T. With plyier. Color coded put them together. I used those electrical cap wires to attach them toguether an electrical tape around it to prevent any moisture. Now working like new. Expend approximately $25. And 20 minutes of my time. (I was being charged for the repair. $250.) Now is working like new. Thanks

Remove one nut top of ice box cut wire and replace temperature sensor in freezer part remove two nuts on back panel and cut wire and add temperature sensor then remove defrost thermostat cut orange and pink wire and twist together new sensor and tape up and one more temperature sensor add bottom of freezer cut and replace and tape up all wire and replace back cover simple easy job

Replaced Temperature Sensor and now it is getting cold.

I removed the old screws and old part. I removed the cover from the fan for room to maneuver. I then took the old screws, used my 1/4 inch socket and screwed the new part right onto the wall of fridge and was done.

Used nut cracker to take out 2screws. Had to take one screw from icemaker, raise it up slightly to get nutcracker accessibility. Price of cake. Ofelder

As per the video , I unplugged the appliance and defrosted the freezer . Then removed the shelves and back from the freezer. Located and removed the old parts and installed the new ones which took about 20 minutes. Reassembled the appliance, plugged it in and it was cold within a few hours. Thanks for all the help