GSE23GGKRCWW General Electric Refrigerator - Instructions

Opened package and just snapped in front insert. Took longer to open package than it took to replace broken insert.

I was able to snap the new piece right in

1 opened door 2. pryed cover off from cieling 3.cut and stripped wires on 4. sodered wires from old wires to new sensor. 5 insulated conection.6 put cover back on. This did not fix the problem it was the control moduel.

I bought the GE Refrigerator about 4 years ago for about $1500. The defrost Heater failed about one year ago. Then I called local repair guy, he replaced the Defrost Heater and charged me about $250. Now it happened again. I think we should try it to fix it by myself. I found the parts from partselect.com, it costs me $50 with 2-3 days shipping. After it replaced, it works fine again.

Note: Symtom: cannot make cool air, Frozen area with frost on the wall. Regeriator "leaking water" on floor since iced food started to melt...

Solution: open the cover of the wall inside of frozen zone, use hot water to defrost it gradually. removed the failed Defrost Heater and replaced it with new one.

Note: after you defrost the area inside of the wall, your refrigerator will work normally without the Defrost heater without any issue about week while you are waiting for the parts coming.

Removed the lower 2 drawers, lower front grill, rear lower compressor cover. Removed the 2 water lines from the quick connects and screws from the water tank. Pulled lines through the hole in the right rear of the refrigerator and removed tank. Then reversed steps to install new tank. The upper plastic tank cover has 2 buttons on top that are really screws with a plastic cap, these are easily removed with pliers.

First:
Remove all shelf’s and drawers from fridge inside that were on the way of the water tank
Second:
Pull the fridge from the wall
Turn off the water supply:
Unplugged the power supply
Third:
Remove the cardboard cover at bottom of the fridge on the back for better access to the water pipes
From the front remove the toe kick for better access at the water pipes
Disconnected the water pipe at the front left side, use a rag or paper towel to hold the water that may drip ( bigger pipe)
Remove the covers on the top of the water tank inside the fridge
Disconnected the water pipe at the back left side ( smaller pipe)
Unscrew the water tank (two screws)
Pull the water tank out with the water pipes attached
Fourth:
Install the new water tank assembly , make sure the pipes goes on the hole at the right side and reaches the from and back
Connect pipes until the line that shows on the pipes
Screw back the new water tank
Put the protections back on the top
Plug the fridge and open the water supply to make sure there is no water leaks
The water is ready to be use

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

NOTE:You can still use your Ice Maker as the water tank is for water dispenser only-only leaked if you pushed on water dispenser;We put painters tape over water dispenser until we got our water tank (Part# PS783769);easy install see below ;NOTE - WATCH VIDEO ON HOW TO INSTALL -ALTHOUGH NOT THE SAME UNIT AS MINE THE PROCEDURES ARE SIMILAR - A MUST
a. Remove food from bottom 3 drawers in refrigerator side so you can remove the drawers to access Water Tank
b. Turn off water
c. Take cardboard off back of Frig (bottom of Frig)
d. Find tubing (short one) that goes to water tank & remove where it connects to the union:located Left side bottom of back of Frig - Push in white lip to remove tubing
e. Remove grate from front of Frig (on bottom) removing 2 screws one far left & one far R (will have to open doors)
f. Find long tubing from Water Tank left side under Freezer door and pull out where it connects to union so you can work on it with Freezer door closed - Disconnect tubing by pushing in on white ring on Union to release tubing.
g. Removed 3 bottom drawers Frig side
h. Removed plastic guard from over light (just pull up on both ends to remove (16 1/2 in long)
i. Remove plastic over top of water tank
j. Remove foam from over top of water tank (be careful not to break foam
k. Take out 2 screws holding water tank
l. Pull out Water Tank and Tubing noting which hole short & long tubing comes out of
m. Install new Water Tank by pushing tubing into holes; Short goes in right hole & Long in left hole
n. Attach Water Tank with two screws you removed, attach foam, plastic cover over Water Tank then plastic over light
o. Short tubing will come out toward back and long hose needs to be pushed under frig toward front freezer door.
p. IMPORTANT NOTE - REMOVE PLUGS FROM TUBING where it connects to Union - I had to undo this part because I didn't notice the plugs
q. Connect Tubing - Short to rear Union by pushing in on white collar on union and do the same with the front long tubing
r. Turn water back on
s. Test Water dispenser to make sure it working before re-installing cardboard on back & grate on front - this is when I found out I forgot to REMOVE THE PLUS FROM THE TUBING
t. Install cardboard on back & grate on front
u. Put in shelves & food back into Frig
v. Because it's quick no need to move food from top shelves

Followed instruction video. Replaced water tank, flushed line from house water. Reconnected line and cycled until tank filled. I have ice and water now.

Unplug refrigerator. Use nutdriver to take two srews out that were holding on the housing. Unplug electric plug and pull out motor and housing. Use hacksaw to cut thru auger holder. Motor will be free to take off,disconnect two wires. Use nutdriver to take out three srews holding motor. Take back cover off and put new motor in cover and reverse procedure. Used new auger wih new motor. Saved big bucks by during this job myself.

1. Removed light cover.
2. Removed old light assembly board from cable, (1 of 3 lights).
3. Connected cable to light assembly board.
4. Replace light cover.
5. All 3 lights fully lighted.
6. Installation Completed.

My father called and asked me if I knew where he could get a new switch light for his refrigerator. I came across your web site and found the part right away. In less than 3 days the part came and my father put it on. He said it was easy and that it was great to have the part come to him instead of having to search all over town. Thanks so much for the fast, easy service.

I just moved the moving parts from the Frame for the humidity level from old to new and all was OK

I pulled the bulb out to see if it was the bulb, no! I took the switch out, of course with the refer unplugged, and jummped out the wires and the light came on. Ordered my switch and put it in in 10 seconds and then there was light! Thanks again for showing me the light!

Tim in NJ

I got the model # off the fridge, ordered the part online. The part was fairly cheap and was at my house 2 days after I ordered it. It was the exact part and I installed it in about 15 minutes and everyting worked out fine and easy and cheap, under $15 total to fix the issue. All I needed to do was use a flathead screwdriver to "pop" out the old switch, remove the 2 wires off the wire connection points, put the wires on the new switch and push it back into place. easy. Great place to get exact parts and fast shipping.