GSE23GGKNCCC General Electric Refrigerator - Instructions

Replaced both temp sensors worked good for 2 days then began freezing food. Looked into it further on line. Found small motorized door broken that controls the cold air from the freezer

The repaire guy came in tooke it out and told me it is goin to coast $20 for the part and $50 for the labor..... So I looked, It was soooo eeezzz ALL you have to do is get the switch out( with help of my butter knife :) it plugs in to a little outlet on the wire (on the botom side) so take out the old one and plug in the new one wich I got for $8 + $6 shipping = $15 THANK YOU PART SELECT for saving me $55 Im a 36 y/o stayathome mom and Ihave never don this before, Im very proud of my self. well... it was very easy!

By reading another customers tip I decided that my problem was the exact same. I had to order the entire motor not just the auger because the motor shaft was stripped. Once you remove the motor, hold the shaft with a pair of vise grips and use a screw driver to turn the auger off clockwise. The threads are reversed. The new auger screws easily onto the new motor counterclockwise and installing back into the fridge was a snap.

removed 3 screws with 1/4 " nut driver, unplugged 2 plugs by prying out on side tabs, removed bracket and motor. Used vice grips to hold motor shaft and used screwdriver to turn auger fork clockwise and remove. Unplugged two connectors from motor. removed 3 screws with 1/4" nut driver to remove motor. changed rubber boot from old motor to new. Reversed procedures to install new motor on bracket, auger fork, bracket in freezer, etc. Only difficulty getting both hands in narrow freezer compartment. Still didn't work, called repairman. When he got here I showed him the problem and lo and behold, now it would not dispense water. He diagnosed it as a bad motherboard, replaced it and all good now. Motherboard $150, diagnose and labor $90, but it is all good now and I even have a spare motor. The failing mother board causes strange howling noises at times and we discovered the compressor fan had also stopped working and in a short while I would have had a bad problem. Caught it just in time!!!

Removed panel from inside the back of the freezer section, by removing four screws. Then, sprayed the ice build-up on the coils, with hot water until all of the ice was melted away. (Note: be certain to plug the drain hole, and use several towels to catch the water drainage. ) Removed the Defrost Heater Element by removing two holding screws. Unplug the unit and pluged-in the new unit and replaced all screws as originally mounted.

Slip out old one, slide in new tray!

There is no access to the inside of the door to replace the water line. I was able to insert a 1/4" drip line barbed connector into the old line at the base of the door and then connect that to a piece of the plastic tubing which I then connected back to the original water supply tubing with the 5/16" union. It took three attempts to get the tubing through the bottom hinge without a crimp in it. It's best to have a second person to hold the door while you "fish" the tubing through the hinge.

Raised side of fridge enough to get 1/4" ratchet with 1/4" socket under roller wheel assy. Removed three hex-head screws to separate damaged wheel assy from fridge frame. From panel below fridge compartment, backed-out stripped leveling screw. Mounted new roller assy and then threaded in new leveling screw from front. Lowered fridge and adjusted leveling screw for proper height. Suggest putting a 2x4 under fridge for safety when hands are under unit.

This part (plastic tubing) does not show up under my model of refrig...so I had to look thru the various water lines and pick the one that "looked" right. Luckily, this is the exact replacement part and works perfectly. I removed the lower back panel from the fridge, removed the bracket holding the water line connectors and pressed the outer ring of the coupler up until it released the old water line. I pushed in the new line, made sure it was snug with a gentle pull and ran the line under the fridge up to the existing coupler. I removed the old line from the existing coupler under the front left of the freezer door, and pushed in the new line. I did not need to use the new coupler. If my old line would not have been so brittle and cracked in several places, I could have just cut out the leaking portion and popped the new couple in to mend the line back together. Easy job and we can stop buying bottled water at the store now!

Checked to make sure water was going to the fridge and it was. Removed the 1st line after the valve and no water was present. Figured the valve was bad. Removed the wires to the old valve and also had to remove the wire harness on the new valve. It wasn't needed. Replaced the valve and installed the old wires. Hooked up the water line and instantly had water. A day later I had a full ice bucket. This part wasn't listed on GE website. But it was on partselect.com.

Easy fix, but they don't give you plenty of wire to work with. When I pulled the switch out it only had about an inch of wire that came with it. meaning if I didn't have a grasp on the wires as I was removing the switch they would have slipped back up the opening

It was very simple! I assessed the situation and gathered my tools for the job. I used a flat head screwdriver, pliers, and electrical tape. I used the flat head screwdriver to release the switch from its location, the pliers to take the electrical terminations apart. I taped the wires individual so that I would not loose them in the door, also not to short them out. I then unpackaged the new switch to install. Pulled the tape off one of the of the terminals while holding the wire, and attached it to the new switchs terminal post. Did the same with the other wire, then snapped the new switch back into place. Immediately had results. I opened and closed the door a few times in amazement that something so annoying such as a light in your fridge could be so easy to fix. Most of all, having a business to rely on to find the part and deliver in a timely fashion. Thank you Partselect.com, you were outstanding!!!

Unplugged the fridge, and opened the freezer. Unscrewed the light panel, small screwdriver. Removed the plastic bracket. Part was frozen and I broke one of the plastic mounts. Do not do this as I am not sure if I will have to live with my cable twist tie kludge or I can get another plastic bracket. Light board is just the PCB. You need to remove the old PCB and install the new one- remember the orientation and the fact that the plastic mount piece has specific sides you can identify by the width of the slots. This is for all the other women like me. Thanks.

the replacement part did not have the 3 screw holes needed to 100% replace the part that broke. however, i realized that the piece that fastens to these 3 screws is the slider cover piece (i dont know its name) that has the rubber gasket was sticking every time i opened the drawer and this was what caused the OEM part to break. anyone who has a GE profile with the meat compartment must know what i am talking about - it sticks and is a bit clunky to open (until the pressure breaks the pin holding the gasket as in my case).
i simply did not place that piece back when i put the replacement part in, and now it slides much more easily. the downside is slightly less seal for the meat compartment, but to me that isnt very important because that compartment does not need to be isolated from the rest of the fridge to do its job.

Tube was too short so I used the union to attach additional tubing to reach the valve at the lower rear of refrigerator