GSE23GGKKCCC General Electric Refrigerator - Instructions

un twist old one and twist the new one

Part arrived very fast as ordered..need to pry old switch out from top..use care to push the retainer down..after old switch was 1/2 out, I used a putty knife for better leveridge.Remove wire connector...after plugging in the wire connector to the replacement switch, make sure the switch is properly positioned so the switch will depress w ... Read more hen door shuts.

Super easy. Hardest part was popping the plastic covers off without breaking them. I had to use a butter knife to get under it & lift it just enough
to grab it & pull easy until it turned loose.

shut off water supply to unit, pull the unit out,unplug, unscrew lower back cover, locate valve relay unit (bottom left, black and clear hose coming out of it) undo the quick connect for the clear water hose on the right (black one is for ice).

front of the unit, bottom left, locate the other hose (longer one) running to the f ... Read more reezer door from under the unit, undo quick connect.

Inside unit, remove middle drawers, careful with the glass panels as these just lay on top and are not fixed.

undo the 3 screws for the old tank, pull it out, snake the hoses thru the grommet on the bottom, reverse process...all set!

The motor shaft stripped and the drive auger spun in place instead of driving the auger to rotate. I had to purchase an entire motor even though the motor itself worked fine. The shaft being stripped had to be hacked off to get the motor out of the assembly. New motor installed, new drive auger installed. Works fine.

Replaced flapper

Dispencer quit working a year ago, but still still dispenced water. I talked to a service technician about it. He told me the electric motor was froze up, so I orderd a new one. When it arrived I installed it in about 20 minnutes,tried the dispencer and still would not work but this time the water would not dispence eather and this time I ... Read more noticed the fan quit running and the light went dim when I tried to dispence ice. So I read the customers diagnosis and repares every thing pointed to the main control board, orderd the part and water filter. When they arrived in three days I watched installing this part video and it took me 20 minnutes to install and every thing works fine.

Remove ice holding box. Remove rear plastic cover (nut driver) Unplug two Electrical connectors. Place unit on work bench. Remove 'U' fork, vice grip on shaft and scewdiver as lever on fork (counter clockwise) Remove motor fron plastic Holder. Install new motor & fork. Reverse removal steps. Actually very simple procedure. Usual c ... Read more ost for this typwe of repair is approx. $300.00.

My GE refrigerator emitted high pitch noise a short while ago. I tried different dampening methods that helped but not eliminating the problem. I finally replaced the fan, motor, and associated parts and solved the problem. The total cost was about $50.

Remove lower front panel, disconnect damaged union from water hose under freezer door, replace with new union, tighten and reattach front panel. No more water coming from under the unit. Ice maker and dispenser features returned to working order!

Using my putty knife, I slid it under the light cover prying upward to remove it. I then unplugged the the light board from the wire and unsnapped from the two prongs. Then reinstalled.

i used the video it showed on the site or iwould not have been able to do it

Disconnected power. Removed evaporator cover in freezer. Removed the bad defrost heater. It is a glass tube about 10" long. The tube was black since the internal heater wire burned out. Use a hair dryer to melt ice in evaporator. Since there was excessive water coming from melt ice, I removed the back panel and took out the white plastic ... Read more drain tube and collected water from the tube in a bucket. I put everything back and used the refrigerator for three days without problem, before the new heater arrived. Then I put on the new tube and everything was fine so far.

I replaced the three sensors, 2 in the freezer 1 in the refrigerator. This was rated as the most common problem. Did not fix the problem. I then checked the ohms on the new sensors then the old sensors they were all within .5 of each other. So I got smart and went down the list of causes on their list. I emailed partselect and asked what ... Read more the parts should read. They replied with that information and it turned out to be the voltage converter on the compressor. I ordered the part on friday payed for overnight delivery and it arrived tuesday. This as you can imagine makes me angry. But the part was easy to install and my refrigerator started working right away. I would advise anyone with this problem to start at the top of the problem list use a multi meter check everything on the list and only replace part or parts that don't come up to standards. This will save time and money and hopefully fix the problem the first time as you are not switching out parts and hoping that it solves the problem.

The evap fan, based on research, appears to be built to only last a few years. Pay attention to your order of removal for all pieces and it will go back rather easily in reverse.Remove items from freezer. UNPLUG FREEZER. Pop out the shelf. Use screwdriver to remove plastic piece in back. Pop out styrofoam piece. Use screwdriver to re ... Read more move back metal section of freezer. Use nutdriver to remove screws holding the fan to the back. Unplug the motor. Pop off the fan. Pay attention to location of all these pieces. Put them on the new motor. Reassemble in reverse. Piece of cake.