GSD3205P00BB General Electric Dishwasher - Instructions

I opened the D/W door, used needle nose pliers to remove the old baffles. They come right out. I cleaned the area using paper towels and installed the new baffles. They just sit in the corners with nothing holding them. Simple job.

I received panels about week after I ordered them, however the large panel came scratched. I immediately called your customer service who was extremely helpful and considerate. She ordered me a replacement and it arrived the very next day..

Excellent service, I was truly impressed.

Based on information gleaned from the internet, I suspected that the drain solenoid might have melted. I took apart the solenoid assembly and checked it out. I found that some of the plastic on the inside of the solenoid had indeed melted, making it impossible for the plunger that opens and closes the drain valve to move in and out smoothly and completely. I removed the old solenoid, replaced it with the new one, and the dishwasher worked perfectly.

Followed the instructions and it was easy. Made the washer seem brand new!...It is the best solutions for a small budget. We used CLR to wash out the washer workings and it really left a sparkle on the dishes... I am so glad you don't change the models so much that parts can't be exchanged when they wear...

After determining the drainage issue was caused by the solenoid, (by process of elimination; the hose was clear, drain opening clear, diverter moving freely, power to solenoid present during rinse cycle= bad solenoid. Solenoid showed signs of overheating upon internal inspection...) I transfered the bracket assembly to the new solenoid, re-attached bracket to diverter reservoir, connected spring and power and Did a test run. Solenoid works great! I did notice the shaft on which the diverter pivots leaking just a bit while moving the shaft. You might consider oredering a new gasket for it if you plan to replace the solenoid. Pretty easy repair. Especially considering the complexity of some other possible problems! Good luck!

Before ordering the parts I read the posts by other do it yourselfers and found them very helpful. I ordered the seal and shaft nut from Parts Select and was impressed the parts were delivered in a couple of days. I removed the two lower panels from the dishwasher to expose the leak and the shaft. I turned off the electricity at the circuit breaker box and disconnected the wiring harness to expose the area I would work on. After cleaning the water deposits from the shaft I pried off the small lock washer and removed the plastic cam from the selenoid. Next step required removal of the push on nut. This was the most difficult part of the entire procedure. It required a bit of gentle but firm pulling with pliers and a couple of screwdrivers, sacrificing the nut in the process. It was better ordering a new one originally then trying to save the old one. Having experiencing these nuts in previous work, I knew a new nut would be a cheap fix! Once off, the old seal is easy to remove. Place the new seal on the shaft as per the included instructions, place the new push on nut and reassemble as originally taken apart. (I used a socket set to push on the push on nut.) I then ran a load of dishes to make sure there was no leak before reinstalling the lower panels. I had no leak but pay close attention to placing the seal and push on nut. The seal must be in the exact place.

I ordered a replacement from partselect.com and received it in just three days. The only difficult part was deciding how to remove the white plastic end caps on the sliding rails. Finally, I took a small screwdrive and pried out the crimps in the metal, pulled the old caps out, inserted the new ones, and squeezed the metal together again using needle-nosed pliers. Nothing to it!
Note: The configuration of the new rack isn't exactly like the original (size and placement of the prongs differ somewhat) but it fits perfectly and works great.

There are 2 switches that should be pressed in when you move the handle to lock door, the switches usually go bad with time. Just take the six screws off on the inside of door, then remove screw on the underneath part of handle. The switches are located on the top part under a piece of 1 inch metal plate held in by a screw, remove that and you'll see the 2 switches, test the button on each one to see if it goes in and out, you'll hear the click to. Just unplug bottom first then the top if you need to replace the top one. Thats it.

I popped off the front track stops--pretty easy with a little twisting and slid the basket out. A little leverage with a screw driver and the roller axle slipped off easily. Popped the new ones on, slid the basket back into the track and popped the stops in place and the job was done in under 15 minutes.

First we got all the water out of the bottom of the dishwasher. Removed the old, melted drain solenoid. Very important - DO NOT THROW ANYTHING AWAY. The solenoid that removed was melted; however I had to reuse the springs, brackets and plunger from the old solenoid. I had to scrape and clean (with a solvent) the metal plunger to reuse it. Once I got it cleaned up and re-used the old parts, mounting it was easy. However, getting that tiny lockwasher on the shaft was a real pain in the ass. Finally I got it together and it worked great.

The repair went smoothly. There were actually instructions included with the parts, so that was nice. The only "gotcha" I found was that . . . after you take off the old food-chopper, you have unscrew the old impeller from the motor shaft. This was a bit difficult and you'll want some good pliers to do it. Don't worry about stripping where the food chopper screwed on-to, that part is attached to the impeller and there is a new one on the new impeller. When I re-installed everything onto the dishwasher, it rattled the first couple of times while the wear-ring was finding it's seat. Don't worry, that's normal. It went away by the third wash. I think I still have a small crack in the pump housing, though. The pump housing is two halves of molded plastic fused together along a seam, and I think the seam is starting to leak. It's about one drop every 45 seconds. I'm thinking JB Weld will fix it.

1. I pulled off the plastic end caps to the top rack that allows the roller wheels to be pulled out of the aluminum rails. You need to push in the raised edge of the plastic caps so they clear the rail slot in order to remove them. This takes a little bit of finger pressure or you can use a flat-edge screw driver to pop them out.
2. Once this procedure is completed, you simply remove the rack and rollers from both rails and remove the old roller wheels and replace them with the new ones.
3. I used a phillips-head screw driver to tighten up the rail wheels before re-installing the top rack into the rails and then re-inserted the end caps. Pliers are handy to help get the end caps back into the rail slots.
4. I finally used a silcon spray on all of the rolling parts of the top tray assembly for lubrication.

I pulled the dishwasher out and detached the drain hose. I attached the new drain hose after cleaning out the connection to the garbage disposal.

Now my dishwasher doesn't stink anymore!

Heard a noise in our dishwasher and ended up taking the entire pump and housing out and found a small sucker stick in the impeller along with a bunch of string and other material that needed to be cleaned out. Also found that the housing was leaking at the shaft that goes to the solenoid and dripping on the solenoid and had rusted the metal plunger that goes into the solenoid. Bought the housing and solenoid unit. 1 screw (bottom one) on the housing was rusted becaue of the water. Had to hacksaw the housing and then had to drill out that screw. Also, the pump housing screen is left hand thread and is tough to get out. Had to hacksaw that too. Be careful of the orientation of the metal ring in the impeller area. I did that backwards the first time and the motor would not move. Also, the electrical connector to the motor appears to be polarized so it can only go on 1 way-notice before you take it out. Be sure to screw the solenoid bracket back on tight and notice the spring orientation before you remove-the new one was different than the old. Bottom line is that it works fine, and for $40, it's fixed, rather than spending $800 for a new one.

I removed the front bottom panels to give me access to the Solenoid area. I did not take out the dishwasher from the cabinetry. I removed the screws holding the solenoid assembly and the C clip holding the hand fan shaped white nylon thing onto the valve shaft. I slipped these to the side. Then I cut through and removed the push on nut with a wire snipper plier. Then I used a knife blade tip to pick out the black seal. I then slipped the new seal onto the shaft, being careful that the flat side was outward, and slid it down the shaft and , with my fingernail, pushed it completely flush into position. The biggest challenge was the push on nut. It does not push on easily and must have the lips pointed outward. It required the use of a 3/8" diamater tube slipped over the shaft to tap the nut down the shaft. This caused the shaft to push into the pump housing, which caused the valve to bind. So I used a vice grip to pull out on and hold the shaft while I tapped the push on nut with a flat head screwdriver. Then I just reversed the solenoid assembly removal. But , when I ran the dishwasher, it no longer leaked.