GR458LXLQ0 Whirlpool Range - Instructions

looked for how to video on you tube. It saved me lots of money. Anyone could do it.

removed the worn out roller...inserted the new roller....tightened the nut...it was finished...this was without a doubt the most pleasent repair from start to finish..only took 3 days from the time i orderded the part to completing the repair...i would advise anyone to use " partselect.com" without hesitation

It was simple. Unscrewed to screws at the back of the oven. Slipped off the wire connectors then attached the wire connectors to the new part, put the screws back in and we were back in business.

removed the two screws that held the cook top on and moved it enough to get to the light switch. Removed the switch and tested with multimeter. Pulled the two wires out of the mounting hole and insulated with elect. tape. Replaced the cook top and installed the two screws that hold it in place. Located the switch at PartSelect on line and ordered it. When the switch came in (the next day), I connected the two wires, and snapped the switch in place, and I was back in business.

Simply removed three screws that held the door trim in place. Once the screws are removed be carefull because the front door glass is held in place by the bottom door trim. Otherwise an extremely easy repair.

I have removed this piece once before and painted it,
but it is difficult to prepare surface.

I tried to replace the part without removing the door
but had difficulty getting the screws to line up.

So, I took the door off. Forgot that you are supposed to jam
the spring hinges in the open position before you remove the door. Manual describes how to do this but picture is not very helpful. So I made two wooden dowels about 3/8" in dia by about 3/4" long. Opened the hinge with a screwdriver and jammed the dowels in place.

Door Trim went on easily and the oven door went back on quickly.

Surprised they don't make this trim piece with rust proof material.

See description listed as problem

Had this range for 6 years. My daughter turned on the burner and it went "pop". She was very upset. I found the best price at PartSelect, and ordered the same day.

the first burner arrived broken in the box. We contacted PartSelect, and they immediately sent another and rushed shipping. It arrived in excellent condition.

To replace the unit: First, I turned off the circuit breaker for the range. Then I removed the two Philips screws that held the cooktop down. Next I removed the nut screws holding the burner to the cooktop.

Then I placed the new burner next to the old one, and one by one swapped the wires (this way I was sure I had the right wire on the right connector). One of the wire connectors broke when removing it from the old burner. PartSelect had provided 4 repacement connector pieces (oddly, all of which were too small for the burner element). So I located a replacement connector at a local hardware store. Stripped the end of the wire and used pliers to fasten the new connector.

After all connectors were secured to the new burner, I screwed the burner to the cooktop, then closed the cooktop and secured it with the two screws.

Turned on the circuit breaker, and it works like new! Saved over $100 by doing it myself!

Ordered a new switch and replaced the old one with it.

My husband pulled the oven out and unscrewed the screws(in the back) the heating element came right out. He did everything on his own. The only thing he needed a little help with was for me to keep the heating coil flush to the back wall of the oven, while he screwed the new one in. It was a very quick job. The longest part was pulling the oven out to get behind it and sliding it back in.

Wire connection was damaged, replaced end piece

My wife did it! I got home one night and my wife had done it! That's how easy it was! Trust me, he is no handyman (woman) but she did it by herself. The part came fast, the price was better than any one else's

Remove three screws, slid old trim piece off door. Slid new trim in place. Used ice pick to align screw holes and replaced screws. Total time about 15 minutes. Tip: used a bead of silicone sealer on the new trim strip to prevent moisture from causing new strip to rust.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

took the handle off, replaces the side trim piece and replaced the handle. Very simple!