GLWN5050M1WS General Electric Washer - Instructions

We pulled off the bottom cover to access the pump. The washer was on its back and that made it easier to reach. There was two hose clamps to pull off along with the two electrical parts. Very easy to replace.

plugged on the wires and hase than snaped in place. the delay of the part was the hard part.

First I located the trouble. I noticed that it was water leaking and figured it had to be a hose. I took the front panel off of the washer and after noticing that the drain hose had a slight hole in it, realized that I could fix it and save myself a repair call. I undid the two hose clamps and removed the hose. I went to a local repair shop that could not guarantee the right part. I went online and found Parts Select.com. I entered minimal information and the picture of the item that I was looking for, the Drain Inlet Hose, was staring at me! Within 3 business days and less than 20 dollars spent, I repaired my washing machine. The total time spent to repair after I received the hose took about 10 minutes. I will definitely use parts select .com and recommend to all my friends and family. Thank you.

First I took the bottom of the washer off so that I could get to the pump then I took a socket set to take the pump off. Then I put the new pump on and put the bottom of the washer back together.

It tooke some time to figure out where the water was leaking. It was from a small hole at the lateral side of the upper third of the drain inlet tube. Removing the hose was easy. Attaching it to the tub with a hose clamp was easy, but attaching the lower end to the pump motor was quite difficult because the spring clamp that had come with the washer was difficult to manipulate. I had to replace it with a band hose clamp.

By the way, the hole in the hose had been caused by rubbing the hose against the drain pipe from the motor to the sink.

I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.

With screwdriver, I removed screws holding old hose in place. Attached new hose and screwed into place.

Unplug the washing machine. There are electrical components that can injure or kill you. Using a screw driver inserted just below the lid of the washer in the front, there are two (2) spring clips that you push on to release. Then the front of the washer tilts down and you remove it and set aside.
On the bottom right you will see the flexible, convoluted rubber hose connecting from the pump to the washer tub. Two (2) clamps hold the hose on. Remove the two clamps, install the new hose and re-install the clamps. Re-install the front panel and push into place, allowing clips to lock into the front panel.

I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.

replaced them & working fine now....

Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!

I followed the video from the website to install the lid switch. Worked like a charm. Great instructions. You do need to supply your own butt splice connectors .

The repair went just like the video! Easier than I would've hoped.

Popped the cap off and put the new one on and it worked. Levels of water can be changed now.

Followed video on You tube that showed step by step how to compete repair.
The machine used in video was brand new and there was no corrosion on any parts so disassembly was much easier in video than on 9 year old machine.
Also reinstalling drive belt was a little tedious but overall job very straightforward and resulted in positive improvements in performance and greatly reduced noise levels.