GLMV169DBB Frigidaire Microwave - Instructions

I purchased one relay switch (there are three) took one out one by one and replced it with the new one and tested it each time until it worked. Super easy and saved me hundreds of dollars by doing this myself.

Much like the other post: 1. Removw vent case on top (3 screws) 2. Remove cover with control buttons (1 screw). 3. Removed bottom relay switch and replaced. Tight working space so be patient. Took 15 minutes Needle nose pliers used to crimp connector onto switch

I managed to move the auger far enough to allow me to insert the cup-drive and then realign the auger with the new cup-drive. I also have had one to break very shortly after installing it. This is my second part to replace and this one went really smooth, since I understood that the initial parts installation instructions did not apply on my ice maker.

Determining the root cause was fairly simple - but one should always identify the basic repair part first that may be the root cause - in this order - Diode - HV Capacitor - Magnetron due to costs of fixing the issue. I found that after replacing the two major components it may have been just the Diod/Rectifier a low coat resolution - but one never knows if the issue was one or many problems that wouldn't allow the Microwave to heat. The team at PartSelect was very helpful and was able to expidite the Magnetron to my residence to start the repair process KUDO's to the Customer Service Team!

My husband did it by just taking off the panel on the top of the microwave and replace old with new. We cleaned up some of the accumulated grease as well on the microwave. He had a little problem with the screws. We have done this before so no big problem. Thanks

Took longer than it should due to no instructions being in box. The removal of the old door took approx 30 secs and was self explanatory. Once I realized I had to remove the plastic inner panel on the new door to re-install it, it also took only minutes. Could have been an easy fix with instructions.

Very easy repair. I popped of the inside plastic door cover with a putty knife, removed screws to old handle, inserted new handle and reinserted screws and plastic cover. It was that simple. The complete job took me under 3 minutes.

Piece of cake. Pryed the cover off of the back of the door with a flat head screwdriver and then screwed in the new handle.

The new door is slightly different than the one I replaced. To install the new door, I had to remove the plastic "frame" on the new door with a small flat head screwdriver. Then, I could easily mount the door to the hinges on the microwave. Once on the microwave, I clicked the frame back into the door and it was good as new!

I found and removed the clip for the door - top on the inside (not easy to find) and then removed the door. Called support who told me to watch you-tube and there were good instructions there. Needed needle nose pliers to hold broken screw and a screw driver that could fit between the metal. Flat head and phillips are required. OH you should try to leave the screw in the hole as getting it back there is a PIA. Took about 20 minutes and I am challenged mechanically. Altogether, not too bad.

Easy as 1-2-3! Removed door from unit (top right hinge has an easy small lock that simply "snaps out" with a standard screwdriver. Placed door face down on table. Removed outer (perimeter) frame with standard screw driver, by plying up. Removed the two screws (to the handle) from the backside of door with a phillips screwdriver. Replaced with the new door handle and repeated the above steps in reverse. Done.

Slipped the screw driver flat tip along the plastic strip near the latch inside of door to pry off the plastic cover to expose the screws holding on the door. Removed 2 screws and replaced handle less than 15 minutes.

on the inside of the door we gently pried off the liner to get ot the hinges ,lifted off the old door, place the new one on ,then carefully popped the inside liner back in place. Door fixed

I used a medium sized flat screwdriver to insert between the upper door hinge pin and the microwave hinge bracket. I applied prying pressure by twisting on the screwdriver and the door fell off. Recommend making sure you have a good hold of the door - It almost got my toes. Installation of new door was a little more concerning with the thought of damaging my new door. I placed the lower door hinge pin into the lower bracket. Placing the upper hinge into position for prying. I recognized it was going to be a tight fit. I used the screwdriver in the same way as take off. I struggled a few times with thoughts of cracking the plastic on my new door, but finally pried enough to get the pin in the hole. The plastic around the inner door popped out of place around the hinge, but snapped back in without damage. A fairly simple project that got my heart throbbing a few times with thoughts of damage control, but all is well that ends well.

Slid old one out and slid new one in (under tabs).