GLEB27M9FSA Frigidaire Microwave Oven Combo - Instructions

Removed old fan and replaced with new fan. To replace fan, the over interior fan blade was removed, then the two slip on wires were removed from the old fan motor, then the three screws securing the old fan motor were removed. The process was reversed to install replacement fan

I purchased one relay switch (there are three) took one out one by one and replced it with the new one and tested it each time until it worked. Super easy and saved me hundreds of dollars by doing this myself.

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

Much like the other post: 1. Removw vent case on top (3 screws) 2. Remove cover with control buttons (1 screw). 3. Removed bottom relay switch and replaced. Tight working space so be patient. Took 15 minutes Needle nose pliers used to crimp connector onto switch

I managed to move the auger far enough to allow me to insert the cup-drive and then realign the auger with the new cup-drive. I also have had one to break very shortly after installing it. This is my second part to replace and this one went really smooth, since I understood that the initial parts installation instructions did not apply ... Read more on my ice maker.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 deg ... Read more rees. So far, works great.

Easy fix for my microwave. The cover just slips out, no tools needed.The best part about this fix was dealing with PartSelect. I recieved my part in less than 3 days but it was damaged. PartSelect overnighted a repacement and I am back in business.

I noticed that the scorched and slightly melted plastic was above a little piece of what looked like cardboard, so I did a Google search for "flames in microwave" or something similar and found a link to a DIY repair site that mentioned a tear in the waveguide cover causing that problem. I ordered a replacement from PartSelect, received i ... Read more t in near-new condition, and replaced the old one with the new one in 5 seconds. I then called PartSelect to let them know that the new part had a couple of "wrinkles" in it that I was concerned might cause a problem down the line but that it seemed to be working OK for now. The nice person in customer service told me that I could use the part for the full year of the warranty and return it if a problem arose. I'm very satisfied with the experience!

Just slide the cover up a bit and it comes out. put the new one in place and slide down into place. done that's it.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe ... Read more into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical suppl ... Read more y. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Disassemble oven door using diagram from website.