GLDA690M00BB General Electric Dishwasher - Instructions

Turn water and electric off. remove\ dishwasher

take of old roller mount and replace new part

















0

Unsnapped the old middle basket, but then still having difficulty getting one side of the old basket to fit in the grooves on the new middle basket. Have tried it several ways, but still just does not seem to be the right fit on that one side.

manual labor.. And a little help from Milwaukee power tools.

The repair piece containing the gasket must be unscrewed and the replacement piece is then screwed into place. Use of a wrench is necessary but used gentle compression as this piece is plastic. Also be careful when starting to thread the piece back on as too much pressure may push the part you are threading it onto out of the back of t ... Read more he dishwasher. ( Note that removing the top rack facilitates the job.. This is done by pushing the locks at the end of the roller tracks in and then to the side, opening the tracks for removal of the rack.)

It was really easy to find the parts in the diagram your website provided. Youtubed the repair instructions....done....thank you very much

Turn off power at electrical panel. Turn off water supply. Disconnect drain hose. Remove dishwasher from cabinet.The drain pump is located under the dishwasher on the front left side. It is connected to the frame with two bolts. Remove these bolts and disconnect the clamps securing two hoses. There were two wires supplying the electric ... Read more al power to the motor. The replacement drain pump was a factory original and matched exactly to the one I replaced . Right product at the right price. Very Satisfied .

I'm 76 years old but still like to repair things as long as I am able to.luckily I had the installation instructions for my washer and they were very well written.I first turned off the circuit breaker to the machine,since it was hard wired,some use a plug in a socket.I then turned off the water leading to the washer. I disconnected the ... Read more water line at the washer and disconnected the wiring. I then pulled the machine out from underneath the cabinet.the drain pump was located on the side towards the back. You have to disconnect the drain hose before you could pull the washer the rest of the way out to lie it on it's back.Once it is lying down it is very easy to remove the drain pump and replace it with the new one. The job shouldn't take more than an hour,however I'm not as agile as I use to be so it took me a bit longer,what with coffee break and rest in between steps. I did get the job done and the washer is working fine.the most difficult part was putting it back under the counter,you have to inch it in and keep feeding the water line and electric cable underneath it. All in all it was a good fix and it kept me away from my IPAD for a while.haha!

Competantly but it still leaks.

Definately purchase all the wheels (8) as they are smaller than original wheels. Buy the wheel with attached stud. Pull off old wheels and pop these on!

I was able to replace the wheels with the new ones I ordered which are a better design.

The wheels on our bottom tray to our dishwasher had fallen off from a lot of use here in our office. When the wheels arrived, I just simply snapped them back on. A few had to be snapped on tight, but there were no tools necessary. Overall, a very easy fix.

Popped the end caps off the rails for the upper basket. Removed the upper basket, turned it over, the upper spray arm with the gasket just fits over and is a 1/4 turn lock fitting, slid the basket back in, reinstalled the end caps, ready to go. So easy even I did it, and we didnt need to buy a new dishwasher when I finished.

Removed all wheels, then removed and installed new studs which were designed better than the origional and re-installed. Bottom rack now slides in and out much better.

put new tub gasket on piece of cake

I ordered 8 wheels, but I really needed just 4.( I am preventing for the future) It was so very simple to place my order and they were delivered in no time. I simply took off the old one, looked at how they were affixed and put the new ones the same way. Less than 2 minutes to do the entire job. I am a "Handy woman".