Models > GLD4560R00SS > Instructions

GLD4560R00SS General Electric Dishwasher - Instructions

All Instructions for the GLD4560R00SS
106 - 120 of 330
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
dishrack was worn and causing chips on dishes
just slid the new rack into place
Parts Used:
Dishwasher Lower Dish Rack with Wheels - Gray
  • Kathleen from LOUISVILLE, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the lower rack wheels had fallen off and melted
The best money I've spent on a repair. Easy. The lower rack now rolls in and out smoothly.
Parts Used:
Single Lower Wheel Stud/Axle Lower Rack Wheel Kit - 8 Pack
  • Alfred from Mashpee, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
one wheel was missing, others kept on falling off
Just snapped studs and wheels together and put them into place.
Parts Used:
Single Lower Wheel Stud/Axle Lower Rack Wheel Kit - 8 Pack
  • ILONA from AUSTIN, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Detergent cap would not stay closed
After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.
Parts Used:
Detergent Dispenser with Rinse Cap
  • Michelle from Carlisle, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheels kept falling off
Removed the old wheels and studs. Pressed on the new studs and wheels. Viola.
Parts Used:
Single Lower Wheel Stud/Axle Lower Rack Wheel Kit - 8 Pack
  • Edwin from Waldwick, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The detergent dispenser latch was broken
The repair was easy. Removed all the screws from the inside door panel, approx. 11. Watch out for that last screw as there isn't anything else holding the outside panel, inside panel and control panel together other than those screws. I then unplugged the old dispenser backed out another 6 screws and replaced the old dispenser with the new one. Put it all back together within about a half hour.
Parts Used:
Detergent Dispenser with Rinse Cap
  • KEVIN from MACKINAW, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishes where not clean after washing
change the nozzles and filter
Parts Used:
ARM SPRAY UPPER Assembly Lower Spray Arm - Gray Middle Spray Arm Fine Filter
  • Daniel from Maurice, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
7 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top rack had the plastic coating coming off
Had to replace the top rack in the dishwasher. Removing the top rack was a tricky. Have to push the tab out not in on the stopper ends of the rack. Unscrew the bolts on the water sprayer. Need to slide the sprayer instead of unclipping it. Real easy to do once it is realized. Should have taken 30 minutes if I knew this in advance
Parts Used:
Upper Dishrack with Wheels
  • Chester from North Las Vegas, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old soap dispensor latch would not hold
Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.
Parts Used:
Detergent Dispenser with Rinse Cap
  • Kenneth from Dublin, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Detergent dispenser did not work
Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.
Parts Used:
Detergent Dispenser with Rinse Cap
  • ARTHUR from OAK PARK, IL
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Difficult to install the mounting screws
Nut driver and philips screwdriver.
Parts Used:
Water Inlet Valve
  • Edward from TUCKAHOE, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No water in
Pulled washer out. Found water inlet valve in lower left. Shut off power and water. Replaced valve with new.
Parts Used:
Water Inlet Valve
  • Everett from FREDERICKSBRG, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door on dishwasher soap dispenser broke.
Repaired the soap dispenser.
Parts Used:
Detergent Dispenser with Rinse Cap
  • Eric from SIMPSONVILLE, SC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken silverware basket
Pulled the old one out and placed the new one right into place
Parts Used:
Silverware Basket with Lids
  • Alan from MECHANICSVLLE, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken axle which hold wheel on lower rack
Easy install, snap in new axle and put wheel on stud. Be sure to check all wheels for any replacement due to heat melting wheels on rack.
Parts Used:
Single Lower Wheel Stud/Axle
  • Robert from WALNUT CREEK, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GLD4560R00SS
106 - 120 of 330