GJP84901 Whirlpool Range - Instructions

Replaced both rollers....Quick and Easy!!

Removed burned out burner, replaced new burner tested works fine

Followed Mfgs instructions.

My wife was complaining about poor baking results with the oven in the home we just purchased, so I hooked up my digital temperature meter and found it was almost 50 degrees of, so I tried the ovens off set program to bring it closer into range. That did the trick ,but she complained about poor baking still. I watched the oven cycle about 8 times and saw her problem. The oven was inconsistent when dropping below set temps, some times it was 20 degrees off, other times it was 80+ degrees off before the element kicked back on. I started with the sensor, it came with easy instructions including wire hi temperature wire nuts if the connectors didn't match... which they didn't. It was very easy to access the senor for replacement. Just unscrew about 10 screws, pull the back access panel off and there it is. Cut the connectors on both ends making sure to leave plenty of wire on each end. Wire nut them together and reinstall the back panel. Reset the oven off set back to zero and check the oven temp watching about 6 cycles. Comes right on now, and her first baking effort came out great...I am pretty sure that was the problem.

I can't believe how easy this was to fix. 1. Unplug the stove. 2. remove the screws that hold the stove top in place. 3. pull the top up, unplug the electrical wires and unscrew the ground wire 4. remove the stove top and flip it over. 4. unscrew braces holding the burners in place. 5. with pliers, remove the wire connections between stove top and old burners 6. replace with new burners. 7. reattach everything. And you're done! Go brag to the neighbors about what you just did.

First of all I couldn't believe parts arrived next day. Parts solved the problem I was reluctant to believe new hinges would solve the problem. I installed the hinges in about 1 hour but I had door apart previously so I knew what I was doing. Now my wife is speaking to me again and she threw the wooden spoon away that she used to hold door closed. Just spent $100 dollars and saved $1600 thanks guys.

The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.

Removed the door. Took out all the screws. Removed the glass that was cracked. Put in the new piece. Put the screws back in place. Put the door back on and it was a done deal.

A breeze. Lifted top, propped it, removed defective element, disconnected wire modules,connected modules to new element, fastened new element, closed top.

Most of the basics have been covered in previous post. I can add this- those who claim 15 minute-fixes are delusional, unless they're appliance repairmen. Secondly- what will take time is the cleaning. If you have to do this repair, which requires extensive disassembly of the door, it would be foolish not to take advantage of the opportunity to thoroughly clean all four layers of glass. Take the glass panes outside and use oven cleaner. This takes time. Other than that, the pancakeing of the components on re-assembly is tricky, but you can do it. Don

The range top came off with two screws under the front portion of the glass top (by the oven door). I unplugged the connection plugs at the rear off the range top, unscrewed the rear screws holding the heating unit in place and plugged in new element and reassembled range unit. You need to removed the two phillip head screws at the rear of the range top in order to remove the bar holding the heating element. Once you do this it is very easy to finish the job.

Removed the right side panel, lifted up insulation, removed element and replaced with new.

I watched the video, purchased the correct heating element and did the repair as illustrated in the video. I simply removed the cook top, removed the ground wire, removed the wiring harness, removed the failed heating element, installed the new heating element and reinstalled the wiring. Piece of cake!

I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!