GIE21LGYDFKB General Electric Refrigerator - Parts

This ice dispenser door flap, also known as a damper door, is designed to seal the ice chute in compatible refrigerator models, preventing warm air from entering the freezer compartment. Constructed from durable plastic and rubber materials, it opens when the dispenser lever is pressed to release ice, then closes to maintain internal temp...Read moreerature and prevent frost buildup. A faulty flap can lead to condensation, frost accumulation, leaking, or ice dispensing issues. This genuine OEM replacement is compatible with select models from GE, Hotpoint, and Kenmore, and restores proper sealing and dispenser function. Installation typically involves accessing the dispenser housing and securing the flap in place.

This is the light switch that goes in your refrigerator. If the light is not working or stays on, you may need to replace the switch. It is made of mainly white plastic, and is an OEM part, directly from the manufacturer. Be sure to disconnect the refrigerator from the power source before you begin this repair. To remove the switch, simpl...Read morey use a flathead screwdriver to pop the switch out from the refrigerator wall, then disconnect the wires. Reconnect the wires to the new switch, snap it into place, and the repair is complete.

This is a replacement evaporator fan grommet for your refrigerator. The fan grommet absorbs the vibration from the evaporator fan motor for quiet operation while it runs. If your evaporator fan is unusually noisy, it could be because the grommet is damaged. This grommet is made of grey plastic and is approximately one inch in diameter. To...Read more access the fan grommet and complete this repair, you will need to remove the evaporator fan motor assembly. This part is sold individually.

This is the replacement door stop, also known as a door stop bracket, for your refrigerator. It is made of black plastic, and is approximately 3 inches long and 1 inch wide. The door stop bracket stops the door from opening more than approximately 90 degrees. The stop can occasionally break, and this will allow the door to open more than ...Read more90 degrees. When this occurs, you will need to replace the door stop. This part is sold individually and is an OEM part.

This plastic shelf support, or shelf stud connects the shelf to your refrigerator. To replace the shelf support first remove the shelves and drawers from your refrigerator, then remove the damaged or faulty stud before installing the new one. This genuine OEM shelf support has an outside diameter of approximately half an inch.

The lid bumper or evaporator fan motor bumper in your refrigerator prevents the fan motor from scraping against the side bracket. If your refrigerator/freezer is noisy, the bumper could be worn down or missing, and the sound could be a result of the motor scraping the side bracket. You will find it between the fan motor and the side brack...Read moreet on the evaporator fan motor assembly. To access the bumper, you will need to remove the evaporator fan motor assembly from the freezer. This part is made of orange rubber and is less than half an inch in diameter. It has a rounded top and a slightly pointed bottom, and is sold individually.

This DC fan motor moves air across the condenser coils and compressor to help remove heat. A failed motor may cause poor cooling, a hot compressor, or humming and squealing sounds. Before replacing it, clean the coils and check the fan blade, wiring, and air path for dirt or damage. Confirm fit with the full appliance model, 4-pin plug, a...Read morend 11.3- to 12-volt rating. Unplug the refrigerator before removing the rear panel. Keep hands away from the blade, protect the cooling lines, and reinstall the panel before testing the unit.

This part is white in color.

This kit includes damper, fan assembly, nozzle and gasket for nozzle. The damper and fan has been updated by the manufacturer to avoid freezing in the refrigerator. Also known as a damper assembly.

The shelf stop in your refrigerator is what locks the shelf into the refrigerator liner. The shelf stop can be found attached to the shelf. To remove the shelf stop, begin pulling the shelf out until the stop hits the refrigerator liner, then depress the shelf stop to remove the shelf. With the shelf removed, you can simply slide the old ...Read morestop out of its groove, and replace it with a new one. This part is made of white plastic and is about 1 inch in length. It is sold individually, and is an OEM part sourced directly from the manufacturer.

This evaporator fan blade is for your refrigerator, and it circulates air so that the temperature of the fridge is regulated. This model has 3 blades, and is a little more than 4 inches in diameter. It is made of white plastic and is sold individually. If your refrigerator is noisy and you hear a clicking sound, it is a good indication th...Read moreat the evaporator fan blade is warped or damaged. If the fridge or freezer sections become too warm, the fan could be to blame as well.