GI6FARXXF04 Whirlpool Refrigerator - Instructions

The old cover was off and I just slid the replacement part that I got from you'll, it just slid in place and snapped close. Perfect fit. Thanks guys

Removed old gasket by carefully pulling it out of the retaining groove. Installed the new gasket starting the corners first and then seating the upper and lower straight portion gently in the retainer groove. Total time for installation was at most 5 minutes. After a week no ice or frost has been found along the bottom of door or freezer. Note: the new gasket came in a small box for shipping purposes and the new gasket was twisted in a v for this purpose. Upon arrival, I laid it out flat on table overnight so it could cool to room temperature and straighten. I would recomend this procedure for a perfect installation.

Replaced water/ice maker inlet valve from video instructions from Just Answer. The inlet tube for the water dispenser would not cede in the valve and this created a leak problem from the water dispenser connection. Called repair tech and he could not get the line to cede correctly in the inlet valve. Am going to request a replacement part. This has been very frustrating!

They send you just the guts, the inner core of the icemaker, and don't include the back piece that has the motor to rotate the screw-drive dispenser and the blower. You get 2 wiring harnesses, and since no instructions come with, you get to figure out which one. The replacement has a few different plugs than the original and those competent can determine which without too much problem. One obstacle was the grounding screw which was inaccessible without removing another part which would have added greatly to the difficulty. I snipped off the old wire and the ring-terminal on the new one and joined the two with a wire clasp. Works like a charm. I had previously replaced the cycling thermostat and checked that the water valve solenoid was within the proper ohm boundaries-don't spend the money for the whole thing without trying those first! Mine must be an odd model because no YouTube videos showed the icemaker from this model.

Layer it out for 24 hrs used hairdryer on med for the wrenkles.

Removed old ice maker by removing 3 screws, unplugged wiring harness. Replaced with new ice maker, placed three screws back to secure the ice maker, plugged wire harness back, and product is working well at this time.

Remove back cover
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.

This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.

I ordered the wrong part for my refrigerator. The refund processed easily. However, the email that I was promised with return instructions has not been sent. I have asked several times about how to return this part and total silence from partselect. I'm ready to throw this replacement bin in the trash.

Saw U tube instrctions how to install and it was easy

The old plactic ring can be removed with flat bladed screw driver, starting on the right side prying it up worked best for me. The new seal snaps in only one way take your time to get it wright.

Don't try and remove the front/handle from the broken pan, you will break it and its double the price of the pan, just use the small hammer to break the pan into smaller pieces and remove handle from them then the handle will just snap onto the new pan. Piece of cake!

Simple. Just put it on the racks provided in the fridge. The part fit perfectly and took literally 5 seconds to put it on.

Pulled the whole assembly out and unscrewed the Ice maker and old wire harness loose. pulled one wire at a time loose and put the new one in place one wire at a time so not to get them wrong. Then the ground wire I cut and stripped and used a wire nut to connect the two green wires together. Otherwise you would have to take more things off to get to the 1/4 nut on the ground wire. Then put the three screws back in the ice maker bottom.Slid it back in place and plugged in the new wire harness. And put the plastic cover back in place to cover the wires. You can also look on U-Tube to see how it is done. They just do not show the new harness I was sent. I guess the ice maker I got fit other models.

Removed the top glass above the vegetable drawers and slipped the center rail in place. And I would like to add that I would do business with this site again!

Failure detected as Damper Control at upper rear of compartment would continuously open/close, would never stay open or closed. Sometimes the main board would turn it off (maybe a low thermistor limit?), but it would stick open a bit, and keeping letting freezer air into fridge. Could have potentially been control board, but as it turns out after disassembly of the defective damper, the internal microswitch was stuck in the closed position so it wouldn't shut off the motor. Easy fix by gently pulling the cover off the damper control, pull out Styrofoam encasement, then a phillips to remove the damper assembly. Gently push tabs to release wire connectors. Reverse the process and you're done! If I really wanted to go on the cheap, I could have just changed the microswitch, but that looked like a shaky maneuver at best. This site saved me on this one, so happy to share my experience with this Maytag and its nasty habit of freezing my milk and eggs!! :)