GHWN5250D1WS General Electric Washer - Instructions

With screwdriver, I removed screws holding old hose in place. Attached new hose and screwed into place.

Unplug the washing machine. There are electrical components that can injure or kill you. Using a screw driver inserted just below the lid of the washer in the front, there are two (2) spring clips that you push on to release. Then the front of the washer tilts down and you remove it and set aside.
On the bottom right you will see the flexible, convoluted rubber hose connecting from the pump to the washer tub. Two (2) clamps hold the hose on. Remove the two clamps, install the new hose and re-install the clamps. Re-install the front panel and push into place, allowing clips to lock into the front panel.

It tooke some time to figure out where the water was leaking. It was from a small hole at the lateral side of the upper third of the drain inlet tube. Removing the hose was easy. Attaching it to the tub with a hose clamp was easy, but attaching the lower end to the pump motor was quite difficult because the spring clamp that had come with the washer was difficult to manipulate. I had to replace it with a band hose clamp.

By the way, the hole in the hose had been caused by rubbing the hose against the drain pipe from the motor to the sink.

Opened lid and place on agitator ... finished

replaced them & working fine now....

I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.

I pulled on the bottom edges of the agitator, like the video said, until my fingers were numb. Finally, after I got aggravated, I beat the old agitator into a hundred pieces with a hammer and chisel. Then I slid the new agitator into place and gently tapped on the top of it. It snapped into place and has worked like a new one every since.

You tube is the only way to go!

I followed the video from the website to install the lid switch. Worked like a charm. Great instructions. You do need to supply your own butt splice connectors .

The repair went just like the video! Easier than I would've hoped.

Followed video on You tube that showed step by step how to compete repair.
The machine used in video was brand new and there was no corrosion on any parts so disassembly was much easier in video than on 9 year old machine.
Also reinstalling drive belt was a little tedious but overall job very straightforward and resulted in positive improvements in performance and greatly reduced noise levels.

As an 89 years old ignorant about washing
machine repairs, I contacted a company to
come and install the new filter, which would have cost me $85,00, just to come, not to replace the filter, that price graduated me to become an instant washing machine mechanic;
but then, I read the extremely easy instructions
how to do the work; I just followed the instructions, and the machine now works like new!.
my order # was 22526491.
The Part # was PS3652834

I was instructed to call 1-888-895-1535
if I needed any assistance; But with instructions so clear, there was no need to call them back.

Thanks Partselect.com !!!

Here is how I did it: and why,
water filter was clogged up.
1: i unplogged the washing machine.
2: I shut off both, the hot and cold water hoses.
3: I removed the water hoses from the machine.
4: I removed three screws from back of control panel.
5: I pulled back the hose clamp between valve and flex hose to shower head.
(if after doing this, the hose will not move,
spray some WD40, and will move fast.)
6: remove two electrical connections on valve,
one on right, and one on left.
7:remove two screws that hold triple water valve to base.
8: replace valve in reverse order above step 7.
that is my friends, if an ignorant 89 years old
did it, you can do it aswell. God bless you all,
and don't forget, this was only possible through the expert assistance of PartSelect.
kindly buy all of your products from them
Call them:1-888-895-1535. Thanks, God Bless

This was one easy job and saved me money by doing it myself, First I unplugged the washer for safety, then I removed the Agitator by grabbing the base of the agitator with both hands and pulling up I set the agitator a side and removed the one bolt holding the agitator coupling in place. the replacement coupling was a little tight when I replaced it due to it being new, (make sure the coupling is fully seated before installing the bolt) reinstalled the agitator plugged the washer back in and tested repair worked flawlessly thanks partselect

Pulled the agitator off by hand. Loosened the screw on top of the coupling and pulled old coupling off by hand. Replaced part with new coupling and socketed it in place. Replaced agitator by-hand by simply pushing it down on top of coupling making sure the plastic teeth aligned.

Watched a how to video. Pulled the agitator. Determined that the agitator coupling was worn out. Matched the old agitator coupling to new replacement one. Ordered it. Pushed the new agitator coupling onto the fitting. Secured it with the old bolt. Replaced the agitator. Repaired.