GFSF2KEYHWW General Electric Refrigerator - Instructions

Unplug refridge then loosened two bolts holding old ice maker. Lower then unplug and removed. Plugged in new harness and tightened two bolts to secure new ice maker. Plug in frig and wait for ice.

Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.

I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.

just had to unscrew old one put the new one in

Replace the motor fan on condenser and clean the condenser

replaced lights in refrigirator and freezer

My son did it , and showed me what he did when he was finished.

Removed the divided glass shelf, to which the slide rail is attached. Removed the broken rail, saved the two screws.
Now comes the clincher:
It would help if the replacement part website would tell you what size and what kind screwdriver you will need, so you could start chasing it while you wait for the part.
Even better if they could include it, since the plastic part and it‘s shipment is not exactly cheap.
So to screw in two screws you need a #15 Star screwdriver!
How many housewife’s have this one in the tool drawer?

I was so pleased I got the correct part on the first try!
I know manufacturers use plastic because it's cheap and lightweight, but these parts break SO EASILY and it's ridiculous. At any rate, I used a Phillips head screwdriver to take off the old part- top and bottom. Then I needed another set of hands (or use the painter's tape) to hold it in place while I screwed in the new part, top and bottom. (2 screws each). Other than needing someone to help hold it in place while I did the first 2 screws, it was simple and one person can do it --You use the masking tape to hold it for the first two top screws if you have no help. Thank you

I replaced the three sensors, 2 in the freezer 1 in the refrigerator. This was rated as the most common problem. Did not fix the problem. I then checked the ohms on the new sensors then the old sensors they were all within .5 of each other. So I got smart and went down the list of causes on their list. I emailed partselect and asked what the parts should read. They replied with that information and it turned out to be the voltage converter on the compressor. I ordered the part on friday payed for overnight delivery and it arrived tuesday. This as you can imagine makes me angry. But the part was easy to install and my refrigerator started working right away. I would advise anyone with this problem to start at the top of the problem list use a multi meter check everything on the list and only replace part or parts that don't come up to standards. This will save time and money and hopefully fix the problem the first time as you are not switching out parts and hoping that it solves the problem.

Received replacement.
Slide the new drawer in place.
Easy!
Perfect fit!
No more problems.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.

1 opened door 2. pryed cover off from cieling 3.cut and stripped wires on 4. sodered wires from old wires to new sensor. 5 insulated conection.6 put cover back on. This did not fix the problem it was the control moduel.

Replaced icemaker assembly. Only 3 Phillips screws to remove the old assembly. Pretty much an exact swap. Was easy to replace but the connecting cable on the new replacement assembly wasn't very easy to make fit. Had to force it into a location that would be out of the way and allow everything to operate properly. That connecting cable should be more flexible and adapt to the fridge a little more friendly.