GFE461LVQ0 Whirlpool Range - Instructions

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

Screwed in light bulb and glass protector

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

Unplugged the range, remove back electrical cover and component cover. Unscrewed old temp sensor and replaced it with new. Oven heats quicker (just by indication) since the probe is only a sensor..

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.

Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]

turn the light on in the oven go to the breaker box and shut off power to the oven when light is out is good indicator remove two screws in back of oven that secure element to back then remove two screws on top inside the oven to almost finish removal. phillips head screwdriver and needle nose pliers and two small spring loaded clamps are all you will need to accomplish thismove the upper element side to side until the connectors are exposed in the back of the stove pull the two wires out about 4 inches should be enough place the spring loaded clamps on each wire so as to not allow them to slip back in the stove body. take the needle nose and while holding the clamp remove the connector from each wire once this is done place the new element in the stove and reconnect the clips on the end off the element move the wires and connectors back into the openings on the stove and replace the two screws replace the two upper screws check all screws for tightness go to the breaker box and turn on the power takes about thirty minutes

Unplug power. Remove panel on the back. Unplug heater.From front remove 3 screws and remove heater. Installed new heater. On the back restored connections - squized the lugs to have better connection. Put panel back. Plug the power and see if the coil get red. It looked good. Used oven few times it works fine. Difficoult part is to clean oven all around from accumulated grease. First repair for this stove, most of the time spend on figuring out what to open, no instructions.

unplugged the range, removed the cooktop left & right front screws, unplugged left & right plug & unscrewed ground wire. Parts arrived fast & reassembled. . Happy, Happy, Happy! Happy Wife...Happy Life!

Removed old trim kit and handle installed new parts but was having problems with glass fitting between handle and bottom bracket there was a gap between glass and handle when installed fist time after disassembling again I found that the door frame it self had to be tapped back into alignment to be square but once the adjustments were made the installation was a breeze

The malfunction was narrowed down to the oven door motor lock, located at the upper left back of the unit. Removed two panels from the back of the unit, 8 screws. Then the motor, 2 screws, 4 wire connectors. Reversed the procedure for the installation, and solved the problem. About 30=35 minutes for the job. If your handy at all, it should not be a problem.