GDWT160R30SS General Electric Dishwasher - Instructions

Very easy - remove the screws around the inside of the door. 6 screws and 2 plugs to remove the assembly. Just be careful not the strip the sheetmetal screws when putting it back together. No screwguns...

I took out the old rack and rolled in the new. I thought I was going to have to take the rollers off the old one and put them on the new, but they were already on the new rack. The hardest part was getting into the box. I am an 80 year old female.

Replaced the original roller connectors with newly designed connectors. Works much better.

It was an install. My problem is that the drain tube is not standard to other dishwashers,so I could not get it at either of the local home improvement centers. The good news is that it is larger than the standard, and offers better discharge.

Simple as 1,2,3.Parts on time and priced right.

I removed six screws and unplugged the module and removed.
Replaced by the new module and plugged in and then replaced the six screws.
Very easy to fix.

I hand removed the snap in wheel axels and replaced the axles with new ones, by hand, no tools needed. On this dishwasher basket the wheeel axels just snap onto the metal cage "wires" of the roll out basket holding the dishes. Very simple. Used pliers to squeeze each old axle retaining nubs,from each of the eight wheels, , then just slipped (pulled the wheels off the axles) and discared only axles (that here the problem, detaching frequently from grasping the pull out dish basket, due to heat taking the temper out of their gripper (to basket).

Just pulled the old axles out and snapped the new ones in and slid them on. Wish all household repairs were this easy.

First, remove the bottom front covers (two parts four screws). Second, remove the two screws at the top that secure the dishwasher to the counter. Third, gently pull away the dishwasher from underneath the counter just far enough to see and be able to remove the door spring(s) - one on each side. Fourth, remove the existing hinge arm link(s) if not already broken off, replace with the new one(s). Note that the door hinge goes on the door (front) side of the spring and the other side fits into a groove on the door arm - the other end of the spring attaches to one of the 3 available holes on the frame at the bottom. It would be a good idea to replace the hinge arm links on both sides even if only one is broken. Make sure that the door has the right tension (each spring can be hooked in 1 of 3 holes to adjust the tension). Then gently push the dishwasher back under the counter. Finally, replace the screws under the counter and replace the covers on the bottom front. All of this should take no more than 15-20 minutes. This was an easy job!

Very easy! Removed 4 screws that was holding the valve to the bracket. Placed bracket over water inlet line. Attached copper threaded coupling with pliers.Screwed valved on to the coupling. Attached bracket to the valve with 4 screws. Reattached water line. Attached bracket to frame of dishwaser. Put kickplate back on and done!

I ordered wheels on this wonderful site that looked like they made more sense and replaced all eight on my dishwasher and FINALLY the dishwasher isn't the nightmare it has been. It took seconds to pop in the clip to the roller and pop it on the rack. Thank you PartsSelect

Very easy, saw the parts I needed online, ordered them, and installed them. Easier than I thought. Saved probably $200 in having a repair man come to the house. Outstanding results! Thank you!

It was very simple to install. At first my husband thought I had ordered the wrong part. I guess they just revamped the part and it worked out really well. And I didn't have it mailed special but I got the parts in about 2 days. My only problem is that the shipping cost as much as the parts.
But the parts are installed and the wheels don't fall off anymore!! If I need anything else I will use your company again and I will tell friends and family about you guys.
Thanks

I only had to repair the wheel axle. Since I read another post stating you don't have to change the wheels, I ordered only the axle and they popped right into the existing wheel and attached to bottom rack better than original design.

The repair was so simple a child could do it. It took less than five minutes and now the drawer rolls smoothly and is quite sturdy.