GDT530PSD6SS General Electric Dishwasher - Instructions

Followed video instructions step by step.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.

Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one

2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.

Had to remove the rubber gasket on the new spray arm to install the device, as it was hard to push into the above slot that fits the arm..

Popped old bracket off with screwdriver, with a then easy installation of the new part.

took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.

Removed the top two screws that hold the dishwasher to the cabinet , remove the two screws on the bottom panel and remove the panel. Screw the levelers all of the way up and pull out the dishwasher about 6 to 8 inch. Hook the new cabe on the spring and pull around pulley and attach it to the door bracket. I replaced both cables. Reverse to complete.

Replace all three spray arms and knocking sound disappeared.
Unscrewed counter clockwise old sprayer arms and lifted. Replaced with new sprayer arms and noise disappeared.

The old gasket pulled right out with no tools needed,
The new gasket went in the same way.

Results:
It did help on one side, but the bottom gasket also needs to be replaced it has a couple of tears one on each end.

Next Steps:
When the bottom gasket gets here I will replace that and it should be as good as new.

1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

Don't remove the door! Unscrew the bolts at each lower corner of the door(this is how the door is attached to the hinges so it is now free). Then open the door fully and slowly pull the door toward you a few inches. This slides the door up the hinges and allows just enough room to slide the old gasket out and and slide the new one in. Then slide the door back down the hinges(pushing it away from you, back into place). Then simply close the door and reinstall the bolts at the bottom corners and all done! I watched several videos and believe me, removing the door to replace this gasket does nothing but turn and small quick repair into a large lengthy one.

youtube youtube youtube!
No videos for the exact unit, but I got the gist from one video which included the trick of holding the door hinge springs in place with allen wrenches, while the door slid up and away for access to the gasket. I also had to pull the unit out from under the counter by about a foot. No need to disconnect anything. Good luck.

Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.

It took longer to uninstall and reinstall the dishwasher than it did to change out the part

1. Take a picture of the old rack in the dishwasher! Just in case!
2. Remove rail channel end caps and place them on the tabletop on the correct side to make sure you put them back on the correct side.
3. Remove old rack.
4. Carefully snap off the water sprinkling unit. (carefully push down tabs so they don't break).
5. Using your picture as a reference (!) snap the water sprinkling unit on the new rack (it's easy).
6. Put the new rack back onto the rail channel and replace the end caps.

Done! Very easy installation ! Rack was not nearly as expensive as I anticipated and was delivered quickly. Note: You get the rack only. All ot the other parts are from the old unit.

The part did not fit at all but not worth it to me to return it. The part I need is about 20 inches in length and the one sent was about 10 inches. I will simply call for this dishwasher to be repaired or replaced.