GDSL3KCXARLS General Electric Refrigerator - Instructions

Removed shelf from refrigerator, screwed on new shelf support, replaced shelf. Got a kiss from my wife for fixing her 'fridge.' Easy!

I lifted the dairy bin up and out. From the top, I inserted the right peg of the new dairy door in place, then gently pushed out on the left side of the bin and down on the left side of the door until the left peg of the door popped into place. Put the repaired dairy bin back at the top of the refrigerator door and pushed it down into p ... Read more lace.

I removed the top shelf and then the existing slide. I replaced the slide and then the shelves.

The only hitch was the need for a special screwdriver which cost $5.

remove shelf above tray to access rail. remove broken rail. use screws from broken rail to attach rail to shelf.

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch d ... Read more islodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back ... Read more in SNAPP

Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!

Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They men ... Read more tioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.

After unplugging the refrigerator-freezer and emptying out the contents I snipped off the refrigerator thermistor, stripped off the wire insulation and used a butt splice. That did not solve the problem. So, a day later I unplugged the refrigerator again, transferred the freezer contents to a newly purchased small freezer unit, took off t ... Read more he back panel inside the freezer portion, and saw a large amount of ice build-up on the silver coils inside. This ice was quickly melted off using a hair dryer and packing towels below this accumulated ice. Then I snipped off the two freezer thermister sensors and the defrost sensor. I soldered the wires together for a hard splice, wrapped the individual wires with rubber electrical tape, and then wrapped that with plastic electrical tape. After re-assembly, the refrigerator-freezer has been working flawlessly for over a week at optimal temperatures.

Must have spent 10+ hours solid looking up info on the internet. Our ice maker had broken years ago, the door flap had broken years ago and I thought this was the end of a fridge after just 6 years 8 months.

GE offered a "broken appliance" warranty for $379 for one year, with no guarantee that when a technician came to look at ... Read more it, the repairs would be covered by the warranty!!! No thank you, you just want me to buy a new fridge. Okay, challenge on, I'll fix it myself.

I took everything from the back of the freezer out. Spent an hour defrosting (note: use hair dryer next time). Ruled out a motherboard problem (even though it appears I have the old style motherboard), removed dust build up from fan intake. I could not get the heater to come on, so I cut off the thermostat defroster and connected the wires together. The only way to get the heater on was to set the freezer control to 0 / zero.

So, ordered part from partselect.com and it arrived the next day!!!. Installed and unit appears to be defrosting okay after a week.

So now I'm back to order the ice maker part. The door flap will wait for another time.

Note: I've put in the time for novices and recognizing how the freezer is constructed.

Time includes taking everything out of the freezer section, unscrewing everything, diagnosing problem, fixing the problem, putting everything back. I would say allow 3-4 hours and pat yourself on the back if you do it quicker.

Note#2, if you have a large build up there is a hole in the floor of the freezer section. If the water does not evaporate it will run out of the hole and into your wooden floors! Place towels both inside and outside the unit just in case!

take the metal cover off the defrost thermostat is on top of the coil take the thermostat off from the coil cut the two wires take the wire and strip the ends off take the new thermostat the wires are color coded wire them together put the thermostat back on coil your done real easy