GDSC3KCYCWW General Electric Refrigerator - Instructions

Needed a square head screw driver.
Appliance man wanted $80 to come out plus parts. Part cost $20 and took 10 minuyto out on. Had to empty half the refrigerator. That took longer than the time to fox

remove shelf above tray to access rail. remove broken rail. use screws from broken rail to attach rail to shelf.

Received new drawer, washed same, removed old drawer and transferred items to new drawer, THEN with out further ado reinstalled same!!! Wa La all finished.

This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!

Removed shelf from refrigerator, screwed on new shelf support, replaced shelf. Got a kiss from my wife for fixing her 'fridge.' Easy!

I lifted the dairy bin up and out. From the top, I inserted the right peg of the new dairy door in place, then gently pushed out on the left side of the bin and down on the left side of the door until the left peg of the door popped into place. Put the repaired dairy bin back at the top of the refrigerator door and pushed it down into place.

Removed shattered glass and inserted the new one into the shelf bracket.

I removed the top shelf and then the existing slide. I replaced the slide and then the shelves.

The only hitch was the need for a special screwdriver which cost $5.

Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

Must have spent 10+ hours solid looking up info on the internet. Our ice maker had broken years ago, the door flap had broken years ago and I thought this was the end of a fridge after just 6 years 8 months.

GE offered a "broken appliance" warranty for $379 for one year, with no guarantee that when a technician came to look at it, the repairs would be covered by the warranty!!! No thank you, you just want me to buy a new fridge. Okay, challenge on, I'll fix it myself.

I took everything from the back of the freezer out. Spent an hour defrosting (note: use hair dryer next time). Ruled out a motherboard problem (even though it appears I have the old style motherboard), removed dust build up from fan intake. I could not get the heater to come on, so I cut off the thermostat defroster and connected the wires together. The only way to get the heater on was to set the freezer control to 0 / zero.

So, ordered part from partselect.com and it arrived the next day!!!. Installed and unit appears to be defrosting okay after a week.

So now I'm back to order the ice maker part. The door flap will wait for another time.

Note: I've put in the time for novices and recognizing how the freezer is constructed.

Time includes taking everything out of the freezer section, unscrewing everything, diagnosing problem, fixing the problem, putting everything back. I would say allow 3-4 hours and pat yourself on the back if you do it quicker.

Note#2, if you have a large build up there is a hole in the floor of the freezer section. If the water does not evaporate it will run out of the hole and into your wooden floors! Place towels both inside and outside the unit just in case!

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.