Models > GDF450PSR3SS > Instructions

GDF450PSR3SS General Electric Dishwasher - Instructions

All Instructions for the GDF450PSR3SS
46 - 56 of 56
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lower try rusting out
Part was incorrect Compare that to GE site saying number on both ports to different parts try to return was half the course of what I paid ridiculous So apparently I'm stuck with it Check GE site you'll see the port is different from what your sound but the numbers are exactly the same No clips to support the utensil tray
Parts Used:
Lower Dishrack with Wheels
  • Ronald from cherry hill, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rusty Lower Rack
Removed lower rack, slid in new Rack.
Parts Used:
Lower Dishrack with Wheels
  • Susan from MASON, OH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rusty upper rack
I simply followed the video instructions and replaced the rack myself, no tools required. Easy peasy
Parts Used:
Upper Rack Assembly
  • Francesca from PALM COAST, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The upper arm in the dishwasher broke.
Followed your instructions and was finished in 5 minutes.
Parts Used:
CONDUIT MID Assembly
  • Cris from BAYFIELD, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old corroded gasket
Replaced gasket with a new one before further problems occurred. Got to get it in but it was relatively easy to place and snap in just make sure it fits on the right place where gasket inside meets ridges on door so it will be on properly for proper fit.
Parts Used:
Gasket
  • Gregory from EXPORT, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mid Spray Arm Assembly not spinning
The Mid Spray Arm Assembly was not spinning due to a dish that was in placed the dishwasher that was too high and hitting the arm. When it spun until it broke the center shaft. Replacement was easy. After removing power I pulled the upper tray out and removed the Conduit Mid Tiered Assembly by unsnapping it from the tray. I twisted off the broken spindle of the damaged arm assembly from the Conduit Mid Tiered Assembly and inserted the new arm and gently pushed it until it snapped into the Mid Tiered Assembly. Reinstalled the assembled parts by snapping into the tray making sure it was centered.
Parts Used:
MID SPRAY ARM
  • Robert from FLUSHING, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower spray arm had melted tips
A quick twist of the locking nut
Parts Used:
LOWER SPRAY ARM
  • Ed from TRAVELERS RST, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spray arm had become unattached and burned by the heat element
It was a simple as: attach and done!
There is a ring on the part that tightens clockwise to the nipple that sprays out the water that it rests on. Twist clockwise and you are done!
It is a mystery how it was unattached to begin with but not a problem in the end, it was easy to fix!

Thanks for sending genuine GE parts!
Parts Used:
LOWER SPRAY ARM
  • Mark De from BRONX, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Kept falling off during use.
Just took old one off & install new one. Snaps on dish rack. Took 5 minutes.
Parts Used:
MID SPRAY ARM CONDUIT MID Assembly
  • John from CLIFFSIDE PK, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Connector to sprayer broke
Connected sprayer aligned on bottom of top rack snapped in place. Very easy to install!
Parts Used:
CONDUIT MID Assembly
  • Melissa from BELLPORT, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old Dishwasher Rack Was Rusted
Piece of cake! Slide old rack out, slide new one in. I wish I had known about this website sooner, would have changed this rack out 2 years ago. Yes, it’s a little different shape than the old one, and Yes, I can no longer put my silverware on the door. BIG DEAL! I would rather move a few dishes around than spend $700. on a new dishwasher. Tell your friends about this website, that will thank you.
Parts Used:
Lower Dishrack with Wheels
  • Elaine from NEWARK, DE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GDF450PSR3SS
46 - 56 of 56