GD0603 Makita Grinder - Parts

The retaining ring fits next to the helical gear. This is a genuine Makita part sourced directly from the manufacturer for use in saws. This part is priced individually and is made of metal. A screwdriver and a set of snap ring pliers might be required during the replacement of this part. It will require replacing if it becomes broken.

This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it has multiple applications based on your tool. Please refer to diagrams for correct application.

This is a Rocker type switch that has internal terminals. This is a genuine Makita replacement part that is sold individually. rnrnSwitches are commonly replaced parts in tools. A switch handles on/off and variable speed operations. They also have a role in electric breaking; they can momentarily reverse electrical polarity. Because sw...Read moreitches use mechanical internals, they will degrade and wear out over time, eventually needing replacement. Some common signs of a broken or failing switch are as follows:rn • The tool has completely stopped functioning - it will not start. rn • The tool operates intermittently, requiring multiple tries to turn on, until eventually it won't start at all.rn • The variable speed function and electric braking aren't working properly.

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

This replacement tapping screw is sourced directly from original equipment manufacturer. It is specially designed for Makita power tools. It is a standard hardware which has multiple applications based on a tool. Please make sure to check appropriate diagrams for the location and use of this screw. This part is made out of metal and it is...Read more sold individually. Requires a screwdriver to tighten/loosen this screw. This is a self tapping screw can tap its own hole as it is driven into the material.

This is a Ball Bearing that is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings minimize friction between 2 parts in your tool that would otherwise spin and rub against each other. The balls or rollers take the load and spin, distributing the weight evenly while the minimal co...Read morentact area of the balls reduce friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is a genuine manufacturer-sourced part which is specially designed for Makita sanders, jig saws, and routers. This cord guard is used to protect the power cord from getting damaged. No tools are required to install the cord guard, simply slide the power cord in place through the cord guard. This part is made of rubber and is sold individually.

This is an authentic HHHH replacement part, sourced from the original manufacturer for use with power tools. The strain relief is commonly used to secure the machine's power cord assembly where it enters the housing set. This item is sold as an individual replacement part, please note the hardware used to secure the part is sold separately.