GCWN2800D0WW General Electric Washer - Instructions

Watched the video. Followed the instructions. This has to be one of the best sites I have ever encountered. Even a caveman could fix the problem after watching the video.

reconnected the wires and turned the water source on

I watched the video and disassembled the machine pretty much the way the video showed. There were a few differences but nothing big. The noise sounded like a dry bearing but wasn't sure where it was. Read the responses and it said it was the tub bearing washer. It made some sense if it was metal on metal. It was a dry bearing (should have listened to my common sense, but these guys know more than I do when it comes to washer repair) on the transmission that had been ruined because of a leaky tub seal, which I also replaced. The transmission was not available at the time of repair (but is now) but that kind of investment may be better in a new unit. There is a video on YouTube that shows you how to replace the bearing, BUT it requires someone with some mechanical knowledge. I'll try it later in the year and if it doesn't work we'll have to purchase a new unit.

I followed instructional video on partselect.com, it was very easy, but it didn't take care of the problem. I got to to order "TRIPLE WATER VALVE" and that did the trick. After opening the washer first time (for water fill nozzle), it took me even less time. You don't have to take the front panel off to replace the water valve.

Repair video is spot on but does not emphasize securing the drain pump to the washer before reattaching hoses. This holds the pump in place allowing you to compress the hose clamp while pushing on the hoses.

I followed the Youtube instructions on replacing the valve. So easy.
Getting the wire clamp pushed back from the hose was the only part that wasn't easy but I got it done by being gentle and persistent moving and twisting the wire a little at a time.
Im a 67 yr old woman and was determined not to call in a appliance repair person after I saw how simple the installation could be. Parts Direct is awesome. Will use again in the future for repairs. I feel like I have super powers after doing this myself.

replaced broken straps all 4. washer not working ]. replaced lid switch with wire harness.replaced bad old belt.working fine now. my wife is very happy. thanks for your videos and how to do the job right.

replace lid switch

Open up the back of the top front panel by removing two screws. Unhook the wires from the old valve, then slip the small clamp down far enough to pull the old valve stem out of the little tubing. Removed the old valve, then replaced with the new valve.

pulled front panel off it snaps in but had to get off. then remove two bolts holding too down. moved top around to get to straps. front to easy 5/16 deep socket aND rather .the other end has 1/4 socket back hard to get too not bad. took 30 minutes. didn't fix problem. on bottom of motor looks like it had rubber bumpers but none there didn't find any on parts list. went to parts house auto got two rubber freeze plugs installed them in hole on bottom of motor that stopped the noise and rube moves very little now. also install new belt . install it put it on motor then on part of pulley then roll pull while keeping belt on motor roll pulley around till belt on all the way then roll pull more pushing on belt on motor till belt fit in all groves then roll it couple more times it will line groves up on pull. install top back down then snap front panel it your done.

Pull hose out from wall and drain water into bucket. Remove two screws from back of washer holding on the clip. Pull hose out from washer its in there about 3 inches or so . If you order a new clip will make this even easier it's only $3.87 and I didn't realize I needed it. So, I just cut the old hose with a small saw near the clip so I could remove it and reuse it. Just slide the clip onto the end of the new hose - it fits into one of the grooves-I just made a note of where that was before removing from old hose. Then replace the two screws on the clip going to the back of washer. Put other end of hose into pipe in wall.

Followed the instructions on repair clinic video

Very easy to put a new water pump. You have to disconnect two hoses from the pump, unplug the power connection from the pump, and unscrew the two screws from the base of the pump.

Removed the two hex head screws from the broken strap and replaced it with the new one. The other three straps were not broken but I also replaced them, again, one at a time. This made sense,since the machine was at least ten years old.

Took off the front panel of the washer which exposed electrical wires going to top lid sensor. Took out old sensor installed new. Cut wires from old sensor and spliced wires from new sensor to machines wires that went to old sensor. Replaced front of washer. Washer works fine now.