GCMX180ED4WW General Electric Dryer - Instructions

The repair was so easy when I got the part, I did it myself without any help in 5 seconds!

I pried out the remaining pieces of the handle out of the door with a screwdriver. When the new part arrived, I snapped it into place and it was done. It fit perfectly.

The end repair was very simple and took minimal effort. The time and difficulty was all in the testing. I disassembled the dryer and removed the drum and then hard wired each thermo-fuse to determine where the fault was. After test all of those I was stumped. When I opened the door the light would not come on so I assumed it was a power fault closer to the source. However after all of my testing I couldn't find anything wrong. I then removed the light bulb and realized it was burned out which led me to the door switch being the fault. I removed the switch and soldered the three wire together and the dryer started right up! All I had to do was order a new $15 part, unsolder the wires and plug them in. Would have been so much simpler if that light bulb hadn't of been burned out causing me to over think my diagnosis. This was my first major appliance repair and I did it with only the help of the parts diagram provided on the website.

Doing some simple troubleshooting with the volt-ohm meter I determined that the door switch was failed.

The replacement door switch restored the motor circuit keeping my dryer in action.

Pulled dryer out from wall, disconnected dryer power cord, removed 3 screws on back that fasten control panel, tilted panel forward, rotated faulty timer to remove it. Removed wires one at a time and connected each to new timer on same connection as on old timer.

I did a search on your site to find out why dryer wouldn't start. It said 25 % of the time it could be the timer knob. Checked my old one sure enough it was cracked.Took old timer knob off and pushed New one back on less than a minute. Thank you for your site. It saved me from costly repairs.

Inserted handle into slots

I simply removed the small black piece and inserted the new knob and it was ready to work. It was so easy and I am very happy. I though I was going to need a repairman but I was able to do it myself. Also, the ordering and delivery was fast and easy!!!!

disconnect power plug unscrew 3 screws in back. lean forward remove button disconnect 2 wires in back of switch. put switch connect 2 wires and button. connect 3 screws in the back. ready to start working

I received the replacement part I ordered from PartSelect.com within 3 days of placing the order. I opened the plastic bag it came in. I snapped the part into the holes left vacant by aforementioned abscence of broken part.

Unplug the dryer.Pull out from wall and remove the torx bolts from the back of the control panel.You'll sort of tilt the control panel back enabling you to reach the dryer timer.Make sure you don't pop out the wires on the other switches.The start button for example(I accidentally did.)Observing the location of the wires on the timer being replaced twist and pop it out.Install the wires onto the new timer and pop it back in.I recommend doing a quick test to see if repair was successful before putting the dryer completely back together.

The repair, from the time that the bulb burned out until it was replaced took about six months. I could have shortened the time if I had ordered the bulb sooner. It was difficult because I had to listen to a fair amount of nagging, which, thankfully, has now ceased. I also had to actually go online and finI opened the dryer door, reached in with my right hand (which happened to be holding the new bulb) and screwed the new bulb in. Tip: Screw it in counter-clock wise. This was not mentioned in the instructions. Come to think of it, no instructions were provided. The company might wish to correct that oversight.

I first throwed the breaker then I took the old bulb out. Put new bulb in. Turned the breaker back on.
It worked great

Removed the broken handle from the dryer and popped on the new one.

First I called to get help with the right part and they told me I needed the pus-to-start-switch. It came in and I called my handyman Ed to install it. I am happy with your service. I dont install but just got the part in.