Models > GBS18HBPABB > Instructions

GBS18HBPABB General Electric Refrigerator - Instructions

All Instructions for the GBS18HBPABB
16 - 30 of 35
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broken shelf end caps- right side of 2 shelves.
After watching video I took off end shelf caps. It took close to 10 mins to replace them.
Parts Used:
Shelf Support End Cap - Right Side
  • William from PRESQUE ISLE, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My freezer door had a retainer bar that became disconnected at one end because the coupling broke.
I slipped the coupling over the bar and then into a door slot. It was very easy.
Parts Used:
Door Shelf Retainer Bar End Cap
  • Robert from SAN DIEGO, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Start relay burned
Unplug the refrigerator removed the condenser/ compressor cover back bottom on fridge, remove the relay from the compressor took off the two wires, replace with new relay
Parts Used:
Overload/Start Relay Combination
  • Carlos from Copper Canyon, OK
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water leaking from under dishwasher
Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.

Indeed, inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.

A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Parts Used:
SCREW
  • Edward from E LONGMEADOW, MA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Socket set, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Frige evaporator fan became noisy then quit working & frige compartment became warm
Came home one evening and found the refer compartment evaporator fan making a noisy/grinding noise. While waiting for the part to arrive the motor finally quit working and the frige lost its ability to cool, but the freezer still worked fine. This is the fan that is inside the frige between the refer & freezer compartments - NOT the fan motor that is located in the bottom/rear next to the compressor. This grinding noise sounded like it was coming from inside the frige and could be easily heard under the vegetable trays and above the freezer compartment. To access this motor you need to go after it from inside the bottom of the frige compartment - there's NO need to remove the refer door. Pull the vegetable trays and remove the small phillips head screw located down in the lower air flow groove toward the front of the refer. Next, pry up & out the front white trim piece that runs the width of the frige. Once that piece is removed you can lift & slide back the whole lower frige trim/tray. Now lift out the large foam block compartment and you'll have complete access to the evaporator fan motor and the evap coils. Simply pull the fan motor assy out, still attached to the triangular bracket and disconnect the electrical pigtail. Next, pull the fan blade straight off the front hub, split & disassemble the motor bracket, & replace both fan motor grommets. Reverse the steps to reassemble the fan motor to the bracket and reinstall back in the bottom of the frige and plug in the electrical pigtail - the fan should (quietly) fire off instantly and begin the cooilng process. Reinstall the foam block, lower frige tray, front trim piece, reattach the phillips screw, close the door, and give it some time - it took our frige overnight to completely cool down. This is not a tough job, I spent more time figuring out how to access the motor then the actuall replacement. Hope these steps help to speed up your repair! And remeber Red Sox 4 Life!
Parts Used:
Evaporator Fan Motor Assembly Fan Motor Grommet
  • Scott from Bonney Lake, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door shelf clip had broken
This shelf has been broken for about a year now and my husband tried several little quick fixes that would work for a while and then the shelf would fall again. A quick search online led me to your website, the part arrive within two days, and the shelf was fixed in less than ten minutes. It's working great. We'll definitely keep you in mind for the future.
Parts Used:
Shelf Support End Cap - Right Side
  • Erika from Joliet, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The retainer latch broke
Removed the shelf retainer and snapped the new one in. and reinstalled the shelf on the door.
This was a very simple problem!
What really impressed me was that I ordered the part from you before noon on one day and received it by 11 AM the next day!!!
Parts Used:
Shelf Support End Cap - Right Side
  • Gary from Clayton, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door shelf retainer broke off
First, I removed the broken end cap from refrigerator door. Then I snapped the new end cap into place. Repair took less than 5 minutes and required NO TOOLS! Easy!! Got my part in one day, Thanks.
Parts Used:
Shelf Support End Cap - Right Side
  • Sheryl from Wyoming, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The end cap on the door shelf snapped off.
I pulled off the broken piece, ordered the new piece, and snapped it on. VERY SIMPLE.
Parts Used:
Shelf Support End Cap - Right Side
  • Miranda from Waterford, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken shelf support on the refrigator door
I matched the part I needed throught your web site. Then I called and spoke to a customer support person, and gave my personal information to her. I do not like giving my credit card numbers over the internet. Your site allows me to do that.
Parts Used:
Shelf Support End Cap - Right Side
  • Matthew from Philaelphia, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
defrost heater would not come on
Removed old defrost heater, cut wire then put heat shrink tubeing on wire,spliced wires slid tubing over splice applyed heat. JOB NONE
Parts Used:
Defrost Thermostat
  • Lawrence from Seaboard, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Smelled electrical/plastic burning. Pulled out refrigerator and noticed small flame near compressor.
Unplugged refrigerator. Removed relay by unclipping wire and pulling relay off compressor. Looked-up part number and ordered part. Replaced part and plugged in refrigerator.
Parts Used:
Overload/Start Relay Combination
  • MARTIN from RIVER FALLS, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Reistall shelf
Replaced cap and reinstalled. But I used iron nail inside cover to hold right side because crack was at right hole and right part would not help.
Parts Used:
Door Shelf End Cap - Left Side
  • Oleg from Lees Summit, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Refrig would not cool, freezer worked fine
Barry G was right on with instructions and expectations of the process to trouble shoot parts and how to replace. Barry also provide the right part numbers for replacement items. Thanks again Barry.
Parts Used:
Evaporator Fan Motor Assembly
  • Edward from McKinney, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broke ice maker supply tube while moving fridge.
Used nut driver to remove two screws at top of tube, and the three screws holding composite cover on back of fridge. Pulled out the upper portion of tube, pulled up on fitting and removed lower portion of tube. Put upper spout portion of new supply tube into position, replaced two screws, pushed lower portion of tube into locking fitting on supply valve solenoid. Replaced composite cover with three screws, and was done. Entire job took less than 5 minutes. It took longer for me to find my nut driver set, than it took to do the repair. I ordered the part online, and it was delivered to my door in a lightning fast 36 hours. Hopefully I won't ever need any more appliance parts, but with your easy to navigate website, fast shipping, and fair prices, you have won me over as a customer. I will refer you to friends because of your high speed, low drag, zero defects, excellent service. Thank you very much. Rich.
Parts Used:
Grommet / Tube Assembly
  • Richard from Boston, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GBS18HBPABB
16 - 30 of 35