GBD277PRS02 Whirlpool Wall Oven - Instructions

Sensor replacement was removing 2 screws and gently pulling on old sensor until the clip comes out. Secured the other end of the wires so that it did not fall back inside. Then connected the new sensor clip to the oven wire, then gently returning wire into oven, and then screwing the sensor into place.
The baking eleme ... Read more nt was easier than the sensor. Removed the 2 screws holding the element into the back bottom of the oven, and pulled the element forward to disconnect from clamps. Inserted new element into clamps and screwed it in. ***NOTE that there will be a smell from the new element. This smell is normal. If the smell continues after a couple minutes stop the oven and wait an hour before reattempting.

2 screws &2 push pull wires.

It was relatively "easy" at age 74. Needed phillips screwdriver and needle nose pliers (not nut driver). Put 2 binder clips on connection wires so they would not fall back behind oven. Figure I saved about $100-$200 for less than 30 minutes work.

Replacement of the thermal overload safety thermostat very straight forward after sliding unit out, killing power and removing two covers. Tested both old and new and both show continuity (= good). Installed new, restored power and tested for proper operation. Didn't happen. Replaced original and now have new as spare. Now suspect the dou ... Read more ble line break relay on electronic control board is failed and source of problem. It is common to both elements and immediate before the suspected thermostat in circuit.

With little reluctance..I decided to change the part myself..but was very satisfied...with two screws to detach the bake oven and install the new one.I was very happy to receive the replacement part within 24 hours of placing the order with Part select.

I found the correct sized light bulb to fit the top portion of my double oven. It fit perfectly and just in time for Thanksgiving.
Thank you Part Select. It was easy to find the right size on your site and my order came in just a few days.

Removed the 2 screws holding the element in place. Unplugged the existing element. Plugged in new element - replaced screws. Took less than 5 minutes. :)

Ordered the glass and read the other reviews/instructions on the PartSelect site. Also read the instructions in my owner's manual for removing the oven door. The hardest part of replacing the glass was the removal and replacement of the door. Once I had the door out, replacing the glass was as simple as removing about 8 or so screws, l ... Read more ifting off the cover and replacing the glass, then replacing the screws. One of the hinges on the door had closed and I was not able to open it to replace the door, so I had to have a neighbor come over to over his muscle power. The hinge problem should not have happened and without that little issue, this is a simple repair that I'm sure saved me at least $100.00 on repairman! And - I'm a woman!

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I used the instructions from another user on this site and the instructions were great. First look in your oven manual to see how to get the oven off-hardest part of repair. Before removing door-duct tape the broken glass. Remove door. Lay door down on flat surface and keep track of screws as you take them out. Remove outer liner-we ... Read more removed 6 screws total. Replace glass with new glass. Reattached outer liner back onto door. Replace door. This is a GREAT site. Thanks.

replaced the suppressor and terminal block oven works

Very simple. I removed two screws holding the oven in place. Slid oven out onto the kitchen floor - it doesn't really weigh that much. I then removed about a dozen screws holding the back panel in place. I removed the back panel, disconnected the thermostat by unscrewing a single screw and pulled the defective part from the connectors. I ... Read more then installed the new thermostat, screwed the back panel back on, slid the oven back into place and re-secured with the two screws. Voila! Repair done. The whole procedure took about 15 minutes and was not difficult at all.

This is a drop in range so I had to remove the range and set on a dolly. Turn the dolly around and acess the THRMST-FIX that needed replaceing, it was open. put the range back in its place and could still use the rest of stove until I received the parts 2 days later .
Pulled the range out put the new THRMST-FIX in put the range bac ... Read more k together and put the range back in place and it has worked ever since.
GOOD JOB

Took longer to take door off than replace glass.The door would have come off easy if I had read the instructions that came with the oven

Removed four trim pieces; removed four wood screws holding oven in cabinet housing; slid oven out (weighs about 150 lbs and takes two people and a bench to rest oven on. Oven will pull all the way out but not much further because of the electric cord.); Removed back sheet metal cover (bunch of small metal screws); removed wires from b ... Read more ad unit, unscrewed the bad unit and screwed in the replacement unit.