Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
fridge door switch did not work
2 of 2 peoplefound this instruction helpful.
stu from richmond, VA
Easy
Less than 15 mins
Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
Light didnt go on
3 of 5 peoplefound this instruction helpful.
dorotea from staten island, NY
Really Easy
Less than 15 mins
Screw drivers
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this helpful?
Thank you for voting!
Dropped a jar onto the pantry and broke the plastic piece on end cap that moved the drawer lid.
2 of 2 peoplefound this instruction helpful.
Terry from N SYRACUSE, NY
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
Removed the lid and pantry drawer. Removed crisper drawer on right side and glass shelve. Removed 2 screws on glide. Removed 2 nuts with nut driver. Gently tugged on the pantry end cap and it released from the back wall. Had to rotate about 90 degrees to remove the extension off the back wall so I could remove the thermostat control arm f
... Read morerom old piece and put it onto the new piece. Gently removed the thermostat control through a series of squeezing pieces and rotations. Do not force anything. Take your time as you are working with plastic that could break at any moment with force. Replace in reverse order.
Read less
Was this helpful?
Thank you for voting!
Tried to level rear wheel without unloading bottom freezer and broke the long leveling bolt.
2 of 2 peoplefound this instruction helpful.
Robert from BRANCHBURG, NJ
Easy
30 - 60 mins
Socket set
Unloaded refrigerator. Pulled refrigerator from wall. Removed bottom panel on back and replaced bolt. Reversed steps but leveled rear wheel before reloading.
Was this helpful?
Thank you for voting!
Bottom drawer access door hinge pin broke of pantry end cap - right side. The pin(knob) is a molded part of the end cap.
2 of 2 peoplefound this instruction helpful.
Neil from E GRAND RAPID, MI
A Bit Difficult
30 - 60 mins
Nutdriver
Removed two 1/4" screws from the end cap with the nut driver and removed it. Transferred a few pieces from the old end cap to the new. Reinstalled the new end cap and presto, job complete.
Was this helpful?
Thank you for voting!
the freezer and refrigerator number would lower it self and eventually get to "-" and "-" essentially shutting it self off!!
2 of 2 peoplefound this instruction helpful.
Marc from SEASIDE, CA
A Bit Difficult
30 - 60 mins
Screw drivers
I replaced the Control Board... the two boards need to be installed first . than plug in the connectors (refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work proper
... Read morely and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..
Read less
Was this helpful?
Thank you for voting!
FREEZEING UP
2 of 2 peoplefound this instruction helpful.
Sherril from ROBBINSVILLE, NC
Easy
15 - 30 mins
Nutdriver
in stalled new circuit board an thermostat an was fixed
Was this helpful?
Thank you for voting!
Refrigerator would stop cooling intermittently, control panel would not display temp settings until power was reset.
2 of 2 peoplefound this instruction helpful.
Jim from HALTOM CITY, TX
Easy
15 - 30 mins
Screw drivers
The video on the part select website with the Canadian gentleman was absolutely the best! My wife and I watched it and was able to accomplish the replacement with no surprises or issues. One tip that we could add is that the orientation of the temperature sensor was not specified in the video, but the slot seemed to work better for one or
... Read moreientation versus another. It has been a couple weeks since the repair and the refrigerator is working like it did when we first purchased it.
Read less
Was this helpful?
Thank you for voting!
Refrig. was not holding proper temp in refrig compartment
2 of 2 peoplefound this instruction helpful.
Dan from Goldens Bridge, NY
A Bit Difficult
15 - 30 mins
Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the
... Read more4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.
Read less
Was this helpful?
Thank you for voting!
Freezer not defrosting and making fridge run warm.
2 of 2 peoplefound this instruction helpful.
Brent from PRESCOTT, AZ
Really Easy
30 - 60 mins
Nutdriver
Super simple following the instruction video you posted. Thanks!
Was this helpful?
Thank you for voting!
Freezer cold ; fridge warm . Freezer not defrosting.
2 of 2 peoplefound this instruction helpful.
Tim from Oxford, MA
Really Easy
1- 2 hours
Screw drivers
Unplugged fridge Pulled light cover off Used screwdrivers to press in on tabs holding control board cover. Unplug wiring harnesses. Snapped board in two. Install in cover Reattach wires Done
Was this helpful?
Thank you for voting!
I broke the parts while moving
2 of 2 peoplefound this instruction helpful.
terry from BLACK MTN, NC
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
Was easier than I thought it would be . Thanks to your diagrams for the parts.
Part was pretty ubiquitous so plastic door pins part fits a lot of refrigs, no tools necessary, new part is flexible enough to bend slightly to fit over pins at side. Mine was a bottom freezer type.
Was this helpful?
Thank you for voting!
Frost on the top edge of the freezer drawer
2 of 2 peoplefound this instruction helpful.
Lee Ann from College Station, TX
Really Easy
30 - 60 mins
Put the gasket in the dryer for 15 minutes to warm it up. It fit much better after it was warm.
Was this helpful?
Thank you for voting!
Empty box sent with no part!!!! No customer service help because of covid
2 of 2 peoplefound this instruction helpful.
Jeffery from MIDLOTHIAN, VA
Very Difficult
More than 2 hours
No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help
My Orders
