FWT449GFS1 Frigidaire Washer - Instructions

I found and ordered a new latch from Partselect.com. After a few days I received the new part. I used a square drive screwdriver to remove the two screws that retained the broken latch, put the new latch in place, and reinserted the retaining screws. The job couldn't have been easier.
I couldn't be happier with the quality of the pa ... Read more rt or the speed of delivery and wouldn't hesitate to order from Partselect.com again.

2 screws out then 2 screws in.

The repair was easy, easy, easy. The part arrived within 2 days after I ordered it. I used pliers to remove the broken knob and replaced it with the new knob. It takes about 30 seconds to fix.

received new part from Partselect within 48 hours! Very simple replacement by unscrewing remainder of old knob counterclockwise. The screwed in new knob in clockwise direction. That was all.

unscrew old knob off and screw on new

I was having issues with the door catch. It looked worn, so I ordered the $10 (plus $13 shipping) part. Replaced the part, same issues. Figured out the hard plastic door catch was just not designed large enough to keep the door (a.k.a. lid) closed. My brilliant brother suggested I just put a piece of masking tape on the tip of the door ca ... Read more tch to enlarge it. Guess what? It resolved the problem. I could have saved $23 and used masking tape that was left in the garage by the previous owner of my house.

I used a shop vac to remove the excess water which would not drain from the drum - this is key to not flooding your laundry room. I removed the 2 machine screws at the bottom of the front panel. The panel removes easily which exposes the pump at the front lower right of the washer. I disconnected the electrical connection on the pump. Usi ... Read more ng the shop vac I slowly removed the hose connectionns at the suction and discharge sides of the pump. Following the disconnect of the hoses screws hold the pump to the base of the washer. Upon removal of the old pump you re-install the new in the reverse order. One item to note is that I purchased 2 hose clamps to replace the spring loaded OEM clamps for the hoses - this greatly aids in reinstallation. Re-install the front cover and you are ready. Total time to repaire 30 minutes - very easy!

Very easy, took off the lower front cover (two screws). Pump is on the right side up front. Took the two screws out that hold it down, unclamped the clamps inlet and outlet hoses. Put a towel under and around pump to catch water befor pulling pump out. Installed the new one in revers order.

I followed the instalation instructions provided with new parts. Getting the mounting pins out was relatively easy However, the shock on the right, behind the pump, was a bit more difficult to remove than the one on the left. I took the rubber drain off the pump in order to get at the pin behind the pump. The new replacement shocks came w ... Read more ith the plastic bushings inserted in the shocks in alternate directions. The original pins were all inserted into the bracket / shocks from the rear so when I installed the new shocks I reinserted one bushing on each shock so they we both oriented in the same direction. The instruction says to be sure the mounting pin is pressed from the side with the busing collar. It seemed strange the shocks came that way, with no mention of switching them. The most difficult part on the installation was pushing the pins back through the bracket and shock since there was no easy way to push the pins in from the rear. I used a large channel locks on the left side, but the right side was more difficult with all of the obstructions. I finally was able to push in place with my bare hands but was very difficult. Sorry to say the new shocks did not cure the vibration at all. I was very careful to make sure the machine is level. I'm not sure if there is a cure other than replacing the machine.

no problemO top loader. open top, disco two electrical plugs and a small hose, then remove two screws that hold valve in place and remove. Re install in reverse order. Thanks for your support Eliot in Alaska!

The door catch on the washer broke, and I had to epoxy the broken catch to finish my laundry. I looked for the part online, and PartSelect not only had the part but had a photo of it as well. I was very impressed with how quickly the part arrived, and within 15 minutes the repair was complete. Thanks for having the photos and getting t ... Read more he part to us so quickly.

Thank you for this web site! A friend suggested the problem being the drain pump, but I was not convinced as the washer would still drain on certain cycles. I took the chance and ordered the part after reading like stories on this website. For the repair: don't forget to lay towels down or have a shop vac ready to collect the water in t ... Read more he lines! The clamps were somewhat difficult to manage as the space is tight, but I did get them off with a medium size adjustable wrench. Getting them back on was a bit more difficult; I gave up on one and put a new o clamp on. It's metal, so I'm sure I would have been better off using the plastic-coated factory clamps.

I started by removing the two screws at the back of the washer and taking the top off of the washing machine. Than I removed the two screws securing the door lok and switch assembly. I disconected the two or three electrical connections and install the new one in the reverse order.

Ordered this part to replace a drain hose that had been cut short on the washer. Installation was straight-forward. Removed the two front screws to access the cabinet. Locate the drain hose and remove with a pair of pliers. Install the new part and attach the clamp with the pliers just like removal. Took about 15 minutes.

Simple install, remove the two screws holding the pump motor.
Loosen the two hose clamps that hold the hoses in place.
Pull out old pump motor.
Place new pump into place, and install mounting screws and tighten.
Slip drain hoses onto new pump and reinstall clamps.
Check for leaks.
Done.