FRT18L4JMJ Frigidaire Refrigerator - Instructions

Remove the broken piece by tilting upward and then sliding straight out.
Simply replace with the new door shelf by aligning the small hooks with the slots on the door. Tilt the shelf up, insert the hooks into the slots and then tilt the shelf back down to its normal postion. It is now locked in place and you are done!

removed the screws in the piece of the rail that was still attached and replace with new one - hardest part was the screw it was so little I started it without the magnetic screw driver - it took about 20 minutes

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

No long shelf came with our new refrigerator, Frigdaire did not have one so I went on-line from you and it fit perfectly, now everything does not have to be in one big heap.

took out the broken, put in the new, lapsed time about 15 seconds. I keep looking in the fridge to enjoy how beautiful the new one looks.

I placed the glass into the shelf frame and then I put the shelf and frame back into the refrigerator.

just snap the new piece in place.

It was fairly easy. Only had to remove the back cardboard. Remove 3 screws and the power plug.
Replacing the screws took a little time the motor mount didn't seem to be tapped exactly for the screws supplied and it was in a tight area. Its working great now.

Pull refrigerator away from wall, being careful not to kink or break water line to ice maker, unplug refrigerator. Using 1/4" nutdriver, remove cardboard lower rear panel, bottom lifts out. Fan and motor are now directly in front of you, grasp the moter to stablize it, and using your other hand, pull fan hub from motor shaft. Be sure motor shaft is clean before reinstalling new fan blade, press new bladr onto motor shaft, until center of blade is centered on outlet side of fan housing. spin blade by hand to insure clearance. Plug refrigerator in and observe operation of fan, refrigerator needs to be calling for cooling for this fan to operate. Reinstall cardboard panel and move refrigerator back into position.

Pull out the shelf and remove the one screw that holds the support rail in place. Remove broken rail, slip in the new one, then replace the screw. Done!

It takes longer to remove items from shelf and clean it than it does to replace the part.

Very easy

Just popped it onto retainer nubs on door. Had been a little concerned, as it was replacing part # 240337900, but it fit just fine.

The broken fan made my refrigerator sound like a lawn mower I pulled the refrigerator out of it's nook and disconnected the power, removed the back panel with my battery powered drill motor, slid the old fan off of motor shaft, slid the new fan back on ran it to make sure the problem was corrected. The entire repair took less than fifteen minutes and was as simple as it could be. Please be careful when cleaning your coil, as the fan is easily damaged if you should contact it.

The most difficult part was the removal of the existing fan and shroud. There is very little room to work between the condenser and the coils where the fan is located. The old shroud had to be removed as it was not compatible with the mounting for the new fan motor and blade. Make sure to unplug the refrigerator and give the coils some time to cool down. The first step was to remove the old fan blade... it simply pulls off. Next you need to remove the two bolts holding the fan shroud to the floor of the refrigerator. Then you need to remove the old fan motor from the shroud... unplug the wire connection and remove two small bolts that hold it on. I was lucky to have a VERY small ratchet to get into these tight spaces. Now is the really hard part, removing the metal fan shroud takes a lot of twisting and turning to get it out. The coils have a little play in them, but you must be very careful of the tubing and connections. Also, the coils are very sharp. Once this is out, IF you can get it out....I had my doubts along the way, you can start to put the new parts in... beginning with the new fan shroud which fortunately is made of plastic and has some give which makes it easier to get in. Then you can mount the new motor to the shroud with the three new screws. Plug in the wire connection, add the foam tape to the shroud and mount the shroud to the floor of the frig with the original two bolts. Lastly, attach the fan blade. This replacement kit is well constructed, fits perfectly and contained all the necessary parts (fan motor with wiring connection, mounting screws, wire connection adapter, fan shroud, foam tape and fan blade), but no detailed instructions come with it. I was lucky to get the old fan shroud out without doing any damage to the surrounding parts, but this part was very difficult for a do it yourself person. I would be interested to know if a professional has some other tips for this part of the replacement process.

I unscrewed the old rails and took the number to order on the first day. The order came on the 3rd day. Can you imagine such fast service.
My daughter is a single mom with 4 children, one of whom was responsible for the breakage. I am the grandmother and was very grateful for the fast service and great price. The drawer was installed in 10 minutes. I just screwed the old screw into the new part and replaced the drawer. Thanks