FRQG7000LW0 Frigidaire Dryer - Instructions

Unplug dryer.
Put up the top of the dryer at the front, remove 2 screws holding the front of the dryer to the sides and remove front of dryer. Locate ignition coil on lower left. Remove 2 screws and bracket over the two ignition coils. Replace coils and reassemble in reverse.
Everybody's happy.

Cover of the dryer pops off and hinges back. Use a flat screw driver to pop the clips on the front sides. Two phillips head screws hold the front panel on. Remove them then lift the panel off the clips at the bottom. Two phillips head hold the Ignition Coil bracket in place. Take note of the direction of the cable connection, it's not marked. Dryer would ignite intermittently. Clothes were not dry after 1 hour.

my experience was just like the other responses. top comes off, 2 screws and the front comes off and the screws to the solenoids come off. Replaced the solenoids and put everything back together.

I purchase one tube of heat resistant adhesive but I change both seals if you could afford to buy a second to I would recommend you do so the one tube just made it. For instructions on how to prepare the drum for installing new seals I went on YouTube

Very simple fix - two screws out - replace handle and reinsert screws. The best part was how quickly I received the parts.

Unplugged dryer. Removed top panel (2 screws top back of dryer). Removed control panel ( Unplugged from control board and 2 screws) Removed front panel with door ( Unplugged light from control board, door switch at connector, and 4 screws) Removed Control Thermister from dryer exhaust blower housing located bottom front of dryer ( Unplugged 2 wires and removed 2 screws ) Installed new Control Thermister and replaced all screws and panels in reverse order. Note: Noticed connector for door switch seemed a little loose when connected correctly. Used electrical tape to reinforce connection. Plugged dryer back in and checked operation. Dryer has been used approximately 10 times since repair with no issues.

Removed burner, unpluged 2 plugs on coils. Removed 2 screws, replaced coils, pluged 2 plugs to coils replaced 2 screws. Reinstaled burner. Dryer works great.

popped in one in

When a teen age girl is going through, what I termed as "Bi-Polar" years (ages puberty to 16), they tend to break things with abnormal strenght and misdirected rage.
In this instance my poor washer took the brunt of her wrath, after 2 weeks of being told to do her laundry. this model of washer is a front loader, and the door locks when operating. she just pulled the handle, a black plastic bit, that broke. I looked up the part, ordered and had the thing fixed within 4 days of it breaking. It was two screws and done. now we can wash clothing in the peace of knowing we can open the door.

Popped the top... disconnected wiring... dropped the front... replaced coils... reversed sequence... done deal. No hassle, no worries, easy as 1-2-3!

I took the old piece off and put the new one on very easy

I simply removed old handle by taking out the 2 screws from back of door and then replacing them into new handle . Repair man quoted me 50 dollars plus cost of part ,which was much higher than Part select price . The itemized drawings on the website are wonderful making it easy to order correct part first time .

Simple: Just removed 2 phillips screws, threw the broken handle in the trash, & put the new one on with the 2 screws. Problem solved.

Followed instructions and the repair went very smooth from start to finish. From getting tools out of tool tray to putting them back it took 15 minutes.

removed the 2 screws holding the handle in place,that was the hardest part as the plastic piece that the screws set into was broken and I had to use a piece of tape to pull the broken receptical out. the rest was a piece of cake. delivery was very fast and ordering was so easy! thank you and I am sure I will be doing business with you again! thanks for everything!