Models > FPI20VSW0 > Instructions

FPI20VSW0 Frigidaire Refrigerator - Instructions

All Instructions for the FPI20VSW0
61 - 75 of 124
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Left bottom part of door rusting out
took door off. sanded rusting hinge and greased. installed door hinge washer. I had to install a larger washer over hinge bearing to help support the door where it was rusting. no sweat. works like its new. thanks to you guys for having the parts.
Parts Used:
Hinge Bearing Door Hinge Washer
  • William from Moulton, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Socket set
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
freezer worked frig was warm. Ice maker is still not working
Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall
Parts Used:
Defrost Timer - 60Hz 120V
  • steve from Kirkland, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken drawer
Bought a new drawer and just used the clear front from the broken drawer. Very easy to replace. Also fast delivery , thank you part select.
Parts Used:
Upper Crisper Drawer
  • Antonia from Germantown, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer built ice, fridge not cold enough and running constantly.
Removed front low grill, removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. Reversed process to install new timer.
Parts Used:
Defrost Timer - 60Hz 120V
  • LUIS from CENTENNIAL, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
coil Iceing up
took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .
Parts Used:
Defrost Timer - 60Hz 120V
  • Thomas from Stuart, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
frezzer iceing over and not cooling the refrigerator
Just removed the two screws and unpluged it.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.
Parts Used:
Defrost Timer - 60Hz 120V
  • Marcus from Pine Hill, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leaking water down into fridge
just like the video showed...it was excellent!!!
Parts Used:
Defrost Timer - 60Hz 120V
  • Ronald from Defiance, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not defrosting and then warm up do to ice
replaced the defrosting timer and saved a lot of $ by doing it my self.
Parts Used:
Defrost Timer - 60Hz 120V
  • Bryan from Red Oak, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broke crisper drawer cover supports
Took off the old crisper drawer cover supports with the screw driver and put the new ones with the screw driver and small hammer (really easy)thank you to your installation instructions video.
Parts Used:
Crisper Drawer Cover Support
  • Ruben from Carson City, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
freezer would not freeze longer than one day. after ten years without problem
pulled out freezer, went to floor,reached in next to compressor pulled off clip just like on the video.Pulled off old capacitator took off wire leads.Installed new one. Freezer runs great.Loaded it up with beef pork and venison. No problems.
Parts Used:
Run Capacitor
  • ronald from deering, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
light socket burned out
snapped the wires from frig onto the proper prong and viola,it works. The proper prong is identified by the size because there are two prongs with the wires and two connecting prongs in the socket. I talked to a very helpful representative and she gave me the number for Frigidaire, when I was confused by the placement of the wire. Wish I had remembered her name to share with you. As it turned out I didn't need to call Frigidaire.
Parts Used:
Light Socket
  • Judith from Gambier, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Heater not coming on - coil frosting up- freezer and Refrig. warm
The instructions given to me by part Select were very good.I replaced the Timer- checked the heater with oham meter it was good- checked the door weather striping it was good and replaced the thermostat with new .So at this point I may need to call a professional unless some one has another solution.
Parts Used:
Defrost Timer - 60Hz 120V
  • James from merrillville, IN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
both ref&frez were hot
1 went with maj 69% said defrost timer. NO. 2 went with second choice run cap NO. 3 went with my thought, ( PTC Starter ) why not, most exp part. Fixed the problem.
Parts Used:
Defrost Timer - 60Hz 120V
  • Gary from Dunnellon, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
freezer was freezing and no refrigerator
Followed instruction vedeo from partselect. THANKS!!!!!
Parts Used:
Defrost Timer - 60Hz 120V
  • Michael E from Uniontown, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken Draw Sliders
Exchanged the front panel of the existing drawer to the new drawer.
Parts Used:
Upper Crisper Drawer
  • Maurice from Bonita Springs, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FPI20VSW0
61 - 75 of 124
Back to Top