FGP337GN0 Roper Range - Instructions

Unsrewed what was left of the trim and oven handle. Just 4 screws total, then replaced the 2 screws of the trim and the 2 screws on handle.
Finished! Replacement parts fit perfect!!! Thanks a milliion!

Removed two screws holding the bottom in, pulled out old bottom, inserted new bottom, replaced screws and tightened them. Total time less than five minutes.

simple change out - remove old grates, install new ones - note that this site/store is excellent

Removed two screws and the front of the door popped off. Replaced the bottom metal piece that the glass front slides into. It was a piece of cake.

I didn't do it, but I suggest putting down newspaper to keep from having to clean up all the charred remains that will inevitably fall from the parts you have to remove. First, unplug the thing so you don't shock yourself. I removed all the racks for easy access to the drip pan, which had to be removed by unscrewing two screws. Then th ... Read more ere was a cover over the flame area that also required two screws being removed. The coil had two screws connecting it, but first I had to pull out the drawer at the bottom, crawl under the unit and unplug the coil. I removed the two screws from the old coil and replaced it with the new one, but first I had to get back under and plug in the new coil. I was unprepared for the virtual small animals that were under the stove, so I took some time to clean out that mess. I tested the thing to make sure it would work, and it did. I put all the pieces back in reverse order and had some really good baked chicken for dinner. I also recommend using gloves, as all the soot is hell on your nice manicure.

removed door handle screws then removed glass retaining tabs from sides put clips on sides of glass held insuation in place and replaced glass replaced door handle replaced two door screws trial opened and closed door successful done

Replaced bottom trim included in kit.
Installed side door trim.
While trying to slide glass front in place both plastic side trims broke.
Had to use already broken door trim and glued in. Just hope when use oven glue doesn’t melt and will have to replace entire oven.

I basically followed the video. The hardest part of the repair was trying to squeeze behind the oven to remove the back plate. Also the original screws holding the igniter took a small Allen wrench that I didn't have so I used an adjustable wrench. One screw was a little difficult but eventually got it tightened. Otherwise this was an eas ... Read more y repair like other reviewers have said.

Igniter is in the back bottom of the oven. I had to take off the top of the broiler compartment which has 3 screws. Unplugged the igniter which has two small screws and used a magnetic nut driver. installed the new one. It took 30-45 minutes.

the research and diagnosis took much longer than the repair on this model. if i had the new igniter on hand, it would have been only about 15 mins.

Remove the side covers. Remove the 2 screws on the back side of the door, hold on to the glass and front panel, they will fall out. remove the 2 screws holding the handle. Put the new handle in place and insert screws, note the old handle had metal inserts that are threaded, the new does not. Had to push very hard and let the screws bite ... Read more into the plastic.

Unplug the electrical cord. Remove all the grates and burner caps. Remove the two philips-head screws on each burner. Slide the plastic putty knife under the cooktop in the front to locate two clips. Push in to disengage clips and lift cooktop up in front. Disengage cooktop from the rear of the range. Remove the bad igniter from the burne ... Read more r head and replace with the new, Disconnect the wire from the spark module and install the new wire. Replace the cooktop by securing the rear first and then lowering into place until the clips engage. Replace the philips screws on the burners and the caps and grates. Plug the range back in and you are done.

Unplug the stove. Remove the burners. Release the top of the stove by using a screwdriver to push in the spring clips on each side of the stove top. Pull out stove to access the back of the stove. Remove the back plates. Identify the defective igniter wire and remove. Install the new igniter wire. Screw the back panels back on. Sn ... Read more ap the stove top back in place. Reinstall the burners. Push the stove back into place and plug in the stove. Test the burners.
One precaution - make sure you do not move the gas tubing under the stove top out of position. If you do, make sure you put it back in line with the gas valves.

new handle arrived black for white oven - screws did NOT fit new handle- glass came off the door when removing old handle

pulled the stove out removed back cover, unplug then unscrew igniter. Mounted new igniter in place, plug it back in , put cover back on, put stove back in place. Took about 20 min. Very easy repair, thank you.