FGHS2342LF0 Frigidaire Refrigerator - Instructions

First I removed two screws per rail and removed the old rails. I replaced with the new rails and used a nutdriver to secure in place. This was extremely easy and I fell like my fridge is brand new again.
You can do it!!!

removed ice maker box and disassembled crusher unit on front of box and installed new housing.

Followed instructions from others on the blog. Shut off water and electricity to the refrigerator. Removed the cardboard plate. Removed the old water valve. Cut the compression valves off and inserted the tubes into the new water valve. Attached the water valve bracket to the fridge. Tightened copper water supply.Turned on the water - no leaks. Plugged the fridge in. Tried the water and ice in the door. No leaks - everything worked perfectly. THANK YOU PARTS SELECT!

I replaced the water valve, but it still did not fix the problem.The old water valve I took out I'm assuming worked fine, I think the real problem is ice building up in pipe or some other blockage.

Parts select was very fast in shipping, very positive experience with them.
I will definitely purchase again from this site.

I recieved the part within 48 hours. I snapped the part in place and I was done in seconds.

Unplugged fridge from outlet. Removed rear panel on freezer side. Removed defrost thermostat from tube and cut wires. Installed new thermostat by matching color coded wires and crimping with supplied connectors and snap back on tube. Reinstalled panel and shelving.

Backed one screw off each side of the shelf brackets, snapped old ones out, snapped new ones in and replaced the screw. Spend more time taking food off the shelf than it did to make the repair

removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.

worked fine

I removed the screws that held the the ice dispencer from the bin. I than removed three screws from the bottom of the bin. I put the new plastic piece on the end of the spiral piece that
pushes the ice. I inserted the spiral piece back into the hole. I than screwed the ice dispencer
to the bin and re-inserted it back in the refrigerator.
It took me about 5 to 10 minutes. It's really easy!

Well...The freezer door bin broke while over-stuffing it with frozen deer jerky. I called my local repair shop and they quoted me what was above retail for the piece...I checked online liked the prices and felt confident to buy from parts select. I bought on a Saturday and selected the slowest shipping (I think 5 days). I got a 'notice' it shipped on Monday and had it Tuesday when I got home from work. Excellent experience.

The old support just unscrewed & then the new one screwed right on with two screws.

The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.

I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.