All Installation Instructions for Frigidaire Range FGF368GMR

Oven not heating up properly

I removed back cover and replaced the probe. The troubleshooting info indicated this is the problem 99% of the time. Guess what, it did not help! Further checks indicate that broil element may be out. Am going to resistance check and order if that is the problem.

Parts Used:

Temperature Sensor

Larry from Jordan, AR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

Convert NGas to LP

The Conversion Kit was throughall with extra fittings and good instructions. My problem was haveing to pay a lisence gas installer $65.00 an hour to do a safety & pressure test. Maybee future Conversion kits would include a cheap disposable pressure tester with hose, then it would be a complete done job by the owner.

Parts Used:

Natural Gas to Liquid Propane Conversion Kit

Randall from Fernwood, ID
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Sliced Outlet Cord

I was replacing a range oven hood, so I pulled the oven away from the wall but left it plugged in. I removed the old oven hood, which had an exhaust pipe that was still mounted through the cupboard. While I was preparing the new oven hood the exhaust pipe fell out of the cupboard and cut the oven wire in half. I was able to find the part number on the existing cord and looked up on line. I ordered the part using 3-5 business days and it showed up in 2 days. I was able to attach the new cord, which had an easy clip plug, and secure back to the stove. Very easy and very inexpensive to do.

Parts Used:

CORD

William from Saint Clair Shores, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Lens cover for oven light broke.

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

Parts Used:

LENS

Amy from Corona, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Aluminium foil fused to the panel

I removed the two back screws, slid out the old panel, then fitted in the new panel (it fit perfectly) and replaced the screws. Five minutes, tops.

Parts Used:

Panel

James from Durham, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Frame that held Glass and Oven handle was bent

removed old frame, 4 screws/ installed new one with old screws.. and wa- la all is in working order

Parts Used:

Black Door Trim Kit

Handle Mounting Screw

Mary Ann from Fresno, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

oven took too long to heat up

un bolted the 6 nut driver heads found probe wire un pluged it 1/4 turn from lock it was in and pull out replace slide in new probe 1/4 turn to lock it in place replace nut driver self tappers and test simple!!

Parts Used:

Temperature Sensor

JAONNE from GAFILED, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

bought a used gas range i have propane it was natural gas

changed the orfices with a 10mm socket and driver handle used an adjustable wrench to tighten the orfice in the bottom of the oven approximately 45 minutes we were using the range

Parts Used:

Natural Gas to Liquid Propane Conversion Kit

Vernon from Moorehead, KY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set

Was this instruction helpful to you?

Thank you for voting!

replace lower oven floor

removded 2 screws at rear of panel, moved panel toward rear of oven, lifted up and out. Slid in new panel in front groove then lowered onto oven floor and secured it with the 2 screws at rear of oven.

Parts Used:

Panel