FGF326WGSH Frigidaire Range - Instructions

First, I read about the experiences of others who did this repair.

Then I removed the oven door by removing the single screw at each hinge - visible when the door is open - using a #2 Phillips screwdriver (the only tool needed for this repair). I placed the door on the kitchen table and removed the two screws at the inside top of the door - they also hold the handle onto the door.

I placed the four screws removed from the inside corners of the door -- into one corner of a tray I used to hold the parts in order. Then I removed the eight screws from the perimeter of the door and placed them into another corner of the holding tray. Then I turned the door over and removed the outside part of the door from the inside - as in removing the cover from a box.

Then I removed four screws holding the middle and outside glass panels and placed them in another corner of the parts tray. Then I removed two screws holding the steel panel against the glass. Then I removed the broken glass from the bottom of the tray. That's when I discovered I had ordered the wrong glass panel.

I called the PartSelect number to return the glass, and while discussing how to return the part, I asked if I had to call another number to get the correct part. The lady assured me she could process my order for the correct part. She was very knowledgable about the system and quickly found the correct part from the schematic. I received the replacement part 24 hours later and installed it within 20 minutes.

Overall a success story. Excellent service and easy work.

remove oven floor and racks remove two self tapping screws unplug igniter replace be careful not to touch element plug in reverse order to reassemble

I removed the oven door using a phillips screwdriver. It was very easy because I didn't have to worry about the door hinges springing the door back. I'm not really handy and it went very easy.

It was so easy. I am 66 yrs old. It only took 30 minutes and a screwdiver. I was totally amazed and I thank you.

Disassembled inside of oven. Slid away from wall opened back replaced safety valve and igniter. Safety valve was good changed only because it was apart. Resemble and test sat. Kept old safety valve for emergency spare.

moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.

It’s a plug in part so other than working on your side while lying on the floor it was a snap. 20-25 mins.

It helps to remove the bottom drawer completely to gain easier access.

Pulled out broiler drawer, removed 3 bolts, plugged in new igniter. Only issue was one of the tiny bolts stripped, so now only have 2 holding it in place.

Followed your video and it was not hard at all

I used the tutorial as a guide, and went ahead with the repair. Because of the older model I was working on there were many more screws to remove, not a problem the repair was simple.

Open the door and slide in the new rack.

I had no experience working on the stove before so it was all new to me. Removed the top cover. Removed the igniters and the burner connections which allowed access to the splash pan. Removed the splash pan and replaced the two broken tubes. Job would have been faster had I known how to access the front burner controls. As a result, we have a fully functioning Tappan range in our kitchen and the range is much better than anything commercially available. They don't make em like that anymore.

It was extremely easy, I took the two screws out by the hinges and then slid the door up off the hinges. After that I removed all the outer screws, a total of 8, and took the panel off. I then had to remove maybe 6 to 8 more screws in order to get to where the inside glass panel was. I then replaced the glass and put the door back together. It was such an easy job, that if anything else breaks rather than assuming I need to replace it Im gonna look on here to see if it can be repaired.

I removed the screws holding the door together,removed the broken panel and replaced it with the new glass
The part fit correctly and the re-assembly was easy.

I removed the four phillips screws to seperate the oven door sections (that lets the door handle drop off too.) and then took out four hex head screws that hold the glass bracket in place. I had to lift out the front glass to reach the broken back glass. After that, I just slipped the new glass into position and reversed the procedure. It took about 25 minutes. It took just about 25 minutes counting the time it took me to find a hex head nut driver. I'm willing to bet it saved me a bundle, too.