FGES3045KFC Frigidaire Wall Oven - Instructions

I watch you tube of how to repair to gain my confidence and attempted the project. It was fairly easy. I took photos of wires so I wouldn’t make any mistakes. Boom ! Finished and works like a charm!!

on the back side of the wall oven the sensor wire was ziptied tight. we had to totally pull oven out of its wall space, remove back panel, unhook zip tie, feed through sensor hole around insulation, connect and then replace back and return and relevel the oven. I have

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as w ... Read more ell as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.

Removed 2 screws located underneath the front lip of the range top. Lifted range top and supported. Removed the 2 screws at either end of the support bracket. This bracket holds the elements in position. Be careful not to let the elements fall out when removing. The elements are now free to replace. Swap out the old with the new and be su ... Read more re to reconnect the wires to the correct terminals on the new element. I did 1 wire at a time so as to not make a mistake at reconnecting the wires. Then replace the support bracket with the 2 screws and lower the range top in place and put back the 2 screws that hold the range top in position. VOILA!! Success. It works. The wife is now happy again:)

Tool old elentment out, put new element in

First, I shut the OFF the main breaker. Then, I removed 2 screws holding the thermostat inside the oven. The wiring harness was too short to pull through small opening. I tried to fish the wires out with a piece of wire, but no luck. Eventually, the wiring harness disconnected and I had no choice but to remove entire wall oven from wall c ... Read more avity.

Before starting this, again, make sure the main breaker is OFF:
1. Remove 2 screws that hold the oven in place. Mine were just below the display panel.
2. Remove silver trim at bottom of oven.
3. The power cable (flexible conduit, running down to the floor inside the cabinet) was too short to pull the oven out of the wall. I had to disconnect the oven wiring at the junction box (again...make sure the main breaker is OFF). I photographed the wiring set-up before disconnecting any wires. Once disconnected, I was able to pull the oven out of the wall cavity.
4. I placed the oven unit on a bar-height stool with a blanket underneath.
5. I removed the sheet metal shield on the back of the oven. (Roughly 10 screws on the sides.)
6. I found the wires to the old thermostat and pulled it through the opening in the back.
7. I disconnected the old thermostat harness, connected the new one.
8. I pushed the new thermostat into the oven and reconnected the 2 screws.
9. Everything looked good. I reassembled the back, slid the oven into the wall.
10. Reconnected the wiring.
11. Turned the breaker back on. Tested and it worked.
12. Secured the stove and installed the trim.

Turned off electricity to the stove top opened up the aluminum cover under the stove top with the screwdriver Took off the wires one at a time with the pliers as they were on tight and replaced them on the new part Replaced the aluminum cover Turned on electricity and voila it worked fine no sparking

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

replaced it

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door ... Read more . Just reverse the way you take it apart to put it back together.

I removed the element, plugged in the new one and that has corrected the uneven oven temperature.