Models > FGEB28D7RF0 > Instructions

FGEB28D7RF0 Frigidaire Refrigerator - Instructions

All Instructions for the FGEB28D7RF0
31 - 45 of 60
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
time to change water filter
first, there many different water filters. your experience will be different according to your water filter type.
Parts Used:
Refrigerator Water Filter
  • Ronald from Warrensburg, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Trim on door water/ice dispenser broke off
Removed two screws and disposed of two broken tabs holding old trim in place. Placed new trim in place, fastened the same two screws. Done.

About two minutes.
Parts Used:
TRIM
  • Paul S Van from BRUNSWICK, ME
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced the water filter
Removed the previous water filter. Installed the new water filter.
I then filled a large glass full of water from the water dispenser several times to clear the air from the filter and lines.

Time to install, less than 8 minutes.

Thank you Parts Select!
Parts Used:
Refrigerator Water Filter
  • Gaylan from ALEDO, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Filter wouldn't engage
Basically unhooked water lines and removed the screws
Parts Used:
Water Filter Base
  • Dennis from OLATHE, KS
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker not making ice
Located problem part of ice maker on web site. Picked the part that had the highest percentage of being the the part that was broken (58% I think). Removed the part, waited for the new part, then put it all back together. Simple. It works great. Thanks for having such an easy web site to diagnose the problem.
Parts Used:
Ice Maker Assembly
  • Guy from FAIR OAKS, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
freezer was causing frost and ice
i put casket on i notice when i received casket in shipping box was bent on the end of the casket 's did not solve problem casket not flush air is due to damage from shipping in the box not happy with the product.
Parts Used:
Refrigerator Freezer Door Gasket - Gray
  • MICHAEL from STATEN ISLAND, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water outlet tubing leaking in elbow behind water filter
Most difficult and time-consuming part of the job was clearing the refrigerator of food and shelving. Replaced tubing as it had split in the factory bend of the tubing directly behind the water filter. Take your time and don't get in a hurry.
Parts Used:
TUBE-WATER INLET
  • Chuck from GRIFTON, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Installed new inverter
Secured bracket. Attached electrical contact to the compressor. Secured inverter to bracket.
Problem: the electrical contact cords are very short, therefore it wa difficult to reach the compressor. Even after connecting to the compressor, the cords are under stress.
However, the refrigerator is working fine.
Parts Used:
INVERTER KIT-
  • LAVAUGHN from MIAMI, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
NO PROBLEM JUST DECIDED IT WAS TIME TO CHANGE FILTER
VERY EASY SLIDE OLD ONE OUT AND PUT NEW ONE IT
Parts Used:
Air Filter
  • Gregory from POTTSTOWN, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original ice maker not working leaking water water out door
Removed exterior housing, sliding old unit forward to release. New unit went in easily. Caution wires don't get pinched.
Parts Used:
Ice Maker Assembly
  • Michael from FREE SOIL, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Our older bin shelf was cracked
Simply removed old shelf and installed new one.
Parts Used:
Door Bin - Clear with White Trim
  • Sheryl from Riverdale, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Flipper mullion assembly broke
Removed 1 screw and unplugged flipper mullion assembly and removed it. Plugged in new flipper and one screw and done. Works as it should.
Parts Used:
FLIPPER MULLION ASS
  • Cynthia from CIRCLEVILLE, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ICE WOULDN'T DISPENSE FROM ICE BOX
I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
Parts Used:
BAR-DRIVE
  • James from ORLANDO, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
3 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ice maker is stuck on crushed ice.
We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.
Parts Used:
Refrigerator Ice Dispenser Solenoid
  • Mary from MAGNOLIA, AR
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No water to the ice maker or water tap.
Removed valve unplugged valve from electric removed water lines from valve and then reverse procedures then turn on water and use.That was it.
Parts Used:
Water Inlet Valve - 4 Coil
  • Laura from LANCASTER, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FGEB28D7RF0
31 - 45 of 60