All Installation Instructions for Frigidaire Refrigerator FFSS2615TS0

The Ice Crusher Did Not Work And The Bin Was Carroded From A Previous Owner

I removed the ice container found the part # on the bottom ordered a new one and installed it. It just slipped right in to place.

Parts Used:

Ice Container and Auger Assembly

Imogene from Truth or Consequences, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 9 people found this instruction helpful.

Was this instruction helpful to you?

I dropped and cracked the door bin

2 steps; 1. I removed the broken door bin 2. I slid the new door bin in place, Am I a genius or what!

Parts Used:

Door Bin - Clear

Melissa from Huntersville, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Frost build up on evaporator

Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.

Parts Used:

Defrost Thermostat Kit

B J from Dillingham, AK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

12 of 24 people found this instruction helpful.

Was this instruction helpful to you?

One of the fridge bins snapped as I used one finger to pull ithe door shut

!st bin that came was broken when it arrived. It was only wrapped in a plastic bag inside the box. The second bin survived although wrapped the same way.....15 seconds to get it snapped in. Do NOT pull the fridge door shut with one finger on the bin!! LOL

Parts Used:

Refrigerator Door Shelf Bin

Tracy from LA CYGNE, KS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Freezer door gasket became loose

Followed instructions for this part from this site and things went well.

Parts Used:

GASKET-FRZR DOOR,GRAY,MAGNETIC

Jerome from Detroit, MI
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

I took the shelf out to wash it and it broke in a million pieces

I ordered a new shelf and I put in, less than minute

Parts Used:

Crisper Glass Insert

Beverly from PHILADELPHIA, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

plastic frame broke in front needed replaced

Well I’ve been cleaning refrigerators for 50 years... so have experience removing shelves etc., for cleaning....I removed shelf and then glass and put new one in........easy peasy

Parts Used:

Refrigerator Shelf Frame (Glass not included)

Roxie from PORT ST LUCIE, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

chrisper drawer jammed found supports were broken

Looked at video on how to remove and reinstall support and followed the instruct ions

Parts Used:

Crisper Cover Support - Front

Crisper Support - Rear

ROMAN from COLTON, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Water dripped from water outlet on door

Replaced the Triple Water Valve

Parts Used:

Refrigerator Water Inlet Valve

Douglas from Denver, IN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Support stude for both vegetable crispers broken off

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

Parts Used:

Crisper Cover Support - Front

RANDY from NORTH CHARLESTON, SC
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Broken parts

needed replacements parts.

Parts Used:

Refrigerator Door Shelf Bin

Meat Drawer - Clear

Mervin from THONOTOSASSA, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 10 people found this instruction helpful.

Was this instruction helpful to you?

One arm on the plastic bin or tray cracked and broke.

This was a replacement part, a simple snap in. What really impressed me was the PartSelect web site and the ease of locating the part and making sure it was the right one. Finally, the price beat out all the others. Since this tray looked like others on the same unit, I needed the details, the different view angles and dimensions to make sure it was correct. No other web site was even close in ease of use or in providing such details. I know I won't waste my time at PartSelect and I've always gotten the right part at the best price.

Parts Used:

Freezer Upper Door Bin

Bruce from Ocala, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

When washing the shelf insert glass piece, it broke into a million pieces.

The repair was just as easy as ordering the part which arrived on day three after I ordered it! I had already cleaned up the broken glass insert, so all I had to do was unpack and lay the new shelf in. Took less than a minute!

Parts Used:

Crisper Glass Insert