FFSC2323TS0 Frigidaire Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
shelf supports broke
-
kelly from Comfort, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Shelf cracked while moving fridge
I removed the shelf and removed the glass (carefully) Cleaned the glass and re-installed it into the new frame that I ordered. Slid the whole thing in the fridge and then put the crisper drawer under the frame. Could not have been easier and the new part is even stronger and better quality than the original.
Parts Used:
-
Becky from Effingham, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wife broke the crisper cover.
Took the other one out and dropped the new one in.
Parts Used:
-
Joe from Yorktown, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water dispenser dripping causing corrosion below tray
Replacement of the water valve repair was a snap. Only the main supply line needed to use a nut to secure the water supply. All other lines were simply cut below the pointed end of the plastic tubing line, nylon nut discarded and simply pushed in to seat with a O-ring fitting. Took no more than 10 minutes to install the new valve and test for leaks after turning water back on. This was the easiest appliance repair I have done in > 5 years, 100% success first time,
Parts Used:
-
Scott from Jensen Beach, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken shelf support stud
Use pliers to remove the broken support. Clear the remaining insert pieces with screwdriver/pliers and insert the replacement part.
Parts Used:
-
Samuel from Camden, SC
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cracked crisper
-
Lynn from NESCOPECK, PA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water was leaking from the old valve
Watched the video on your website and you can’t go wrong.
Thanks for being there
Mike
Thanks for being there
Mike
Parts Used:
-
Michael from Double springs, AL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers, Wrench (Adjustable)
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Crisper drawer cover and support
Removed broken parts and installed new ones. Only had a little problem getting supports out. I think they had sticky stuff from spills in the refrigerator that made it more difficult.
Parts Used:
-
Roland from CHAMPLIN, MN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
During cross country move, water valve froze and broke.
Straight forward repair. Remove the four screws holding cardboard back. Remove the 2 screws holding the valve. Unscrew the water lines and unplug the electrical connections. I would caution that it would be wise to either take a couple photos or write down the order of connection. Even though it is somewhat color coded and the water lines are different sizes, a photo removes any confusion. My old valve had threaded connections using brass nuts and ferrules. The new valve has push in connections so you need to cut the ferrules off.. When cutting off the tubing, be sure to cut square. An angled or "squished" cut will leak when pushed into the fitting. Attach the valve to the refrigerator with 2 screws and replace the cardboard back and you're finished. While you have the back off is a good time to clean the coils. I left my fridge out and back off for a couple of ice making cycles so I could check for leaks (how I know the tubing needs to be cut very square). All in all, a very easy fix.
Parts Used:
-
Eldon from HALLAM, NE
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Wrench (Adjustable)
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old crisper drawer cracked
Took out old drawer. Removed clips from that drawer in rear and clipped onto new. Removed humidifier control from old and inserted into new. Slid drawer onto track.
Parts Used:
-
Joel W from LAUGHLIN, NV
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Crisper Glass was broken
Took the glass out of the shipping box and it just slid right in. It was a perfect match.
Parts Used:
-
David from PFLUGERVILLE, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I let value was leaking its self
Undo a few bolts unplug power and unhook water lines then recut all lines and push in to new value
Parts Used:
-
Mitchell from FOXWORTH, MS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench (Adjustable)
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
glass shelf was broken.
Well, after watching the video before ordering the part, I ordered the correct part. My wife had ordered the wrong part that I had to return and ordered the correct one. To install the glass you just take out the crisper above shelf and lay the glass in place. So simple.
Parts Used:
-
Virgel from NEWNAN, GA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken crisper pan guides
Nothing exciting - just replaced the defective drawer covers with the new parts. The guides are poorly designed. the bottom guides on both covers failed.
Parts Used:
-
Ronald from DINGMANS FRY, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Valve body separated : major leak.
-
Robert from NASHVILLE, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!