FFHS2622MSWA Frigidaire Refrigerator - Parts

This crisper cover front support is used to keep the crisper shelf in place and may need replacing if the door will not open or close. This white, OEM part measures roughly 1 inch in diameter and can be used for the front and the rear support, as designed by the manufacturer, and mounts to the inside cabinet wall. Replacing this part is a...Read moren easy repair, and will require a small flat blade screwdriver, a putty knife, and a soft hammer. Remove the crisper and shelf from the refrigerator before replacing the support. The crisper cover front support is held in place with a locking pin. To remove the old part, you will first need to push the pin into the interior of the cabinet using the screwdriver, and then you can pull the support out with a putty knife. If you cannot get the pin out you can use a flat-blade screwdriver to push it down and out of sight and it will not harm anything in your refrigerator After removing the pin and attaching the new support, simply use the soft hammer to lock the new pin in place.

This authentic rear crisper support is a white, plastic part which is rated as "easy" to install by our customers. This OEM part replaces the rear crisper cover support in your fridge and mounts to the inside cabinet wall. If there is visible damager or your crisper stops fitting properly, it may be time to replace the part. Check your us...Read moreer manual and model number to ensure this part is what you need. Replacing the rear crisper support in your refrigerator is an easy job. This part is made from plastic and mounts on the inside of the wall. To complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually. Please note that the rear and front crisper support are different parts; this is the one you are looking for if it is your rear support that needs replacing.

This part releases water from the supply line when it's activated. NOTE: This part may appear different than the original, but is an authorized manufacturer replacement.

This door bin holds items on the door of your refrigerator. They are sometimes called Cantilever Shelves as they attach to the refrigerator door by the back of the shelf. This part is sold individually.

This 40-watt appliance light bulb is a reliable replacement for use in select ranges, refrigerators, freezers, and microwaves. It provides bright, consistent lighting to help you see clearly inside your appliance. Installation is simple—just unscrew the old bulb and replace it with the new one. If the existing bulb is broken, disconnect p...Read moreower and use needle-nose pliers to safely remove the remaining base. Sold individually, this bulb is a commonly replaced part—consider keeping a spare on hand.

This NSF-Certified OEM filter is white in color with a plastic housing and extruded carbon filter media. It measures 2.3-Inches deep, 9.1-Inches high and 2.3-Inches wide. It fits certain Frigidaire side-by-side models after 2009 that use a water filter located in the back, top right. Filters all dispensed drinking water and the water used...Read more for making ice. It minimizes chlorine flavor and smell and cuts down on common contaminants by 99 percent. You will need to replace the filter every six months or when the light indicates. To install the new filter slide it into the housing and push until it locks in place. Press the indicator button for ten seconds to reset after replacing.

This original equipment manufacturer Door Shelf is a white plastic part which holds items inside of your freezer or refrigerator door. It is roughly 10 inches long by 4 inches high by 5.5 inches wide. It can be used in the freezer or refrigerator and is very easy to repair. All you need to do is snap the new door bin into place, which req...Read moreuires no tools. This part is sold individually and not as part of a set, even though your refrigerator may take more than one of this part.

This OEM white door bin is made of white plastic and is easy to install. It is used to hold items in the fridge, and you'll be able to visually see if the part is broken. This part attaches to the fridge door. You can check if this model is right for your appliance by checking your user manual and model number. The size of this door bin i...Read mores approximately 15.42 inches wide x 7.1 inches deep x 5.04 inches in height and holds 1 gallon. No tools will be required to complete this repair, which our customers rated as very easy, and only takes a minute. Just pop the old part out of place and snap the new one in. This part is sold individually.

The run capacitor is attached to the compressor. This part is 120 volts and 15 mfd. The run capacitor helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. If your refrigerator is too warm, will not start, or your freezer section is too warm, you may need to replace this part....Read more This is a genuine OEM part. Please remember to disconnect power to your refrigerator before starting your repair.

This 8-cube ice maker is used to create ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold in to the ice bucket. The ice maker will continue the process until the ice bucket has reached the l...Read moreimit. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

This clear plastic crisper drawer is for side-by-side refrigerators. It is sold individually and sourced right from the original manufacturer. Please note that the new pan does not have the humidity control slide, and this component is now sold separately. The crisper drawer is designed to store produce at a humidity level that ensures yo...Read moreur food is kept fresh for as long as possible. It is commonly replaced because it is cracked, warped, or stained. For this simple tool-free repair, start by opening your refrigerator door and sliding out the old crisper drawer. Take your new crisper drawer and align the thin ridge on the top of the drawer with the track located inside the refrigerator. Slide the new part into place and your repair is complete.

Keep your produce fresh and your fridge organized with this crisper pan cover frame. It fits above the bottom drawer and helps control humidity levels for fruits and vegetables. The frame is sturdy and easy to install, but please note that the glass shelf is not included and will need to be purchased separately to complete the setup.