FFHS2311LWNA Frigidaire Refrigerator - Instructions

Fridge has Ice & water in Door.
Slide bottom plate out.Remove three screws
across bottom.
Remove two screws that holds a circut board.
pull the water hose off and remove board.The hose is a little tricky getting back on.

remove two screws that holds two little plates and remove old part.
Reverse prosedure to put back.

We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.

Watched repair video on plastic auger repair and decided to just invest in the whole replacement unit. 45 minute vs. a 5 minute repair.....no brainer. Removed shipping materials from new dispenser, placed on counter top. Removed old ice dispenser, dumped existing ice into new dispenser. Installed new dispenser with ice back into freezer. Tested and unit now dispenses ice.. Easiest fix I've done to date.

Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...

Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all of the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.

Twisted replacement bulb into place easily. Let there be light!

Took the ice storage bin out. Took the unit apart,and disamble the augar unit. Ordered parts from manufacture, which arrived in two days. As soon as I got the parts, I reassambled it. Work perfect. Good job!

very easy to do. just snap into place

Removed screws holding unit and removed unit. Removed switch from connectors in unit. Replaced unit without switch. On day switch arrived (delivery was prompt) my wife replaced switch by attaching the two connectors and slipping into unit without having to remove entire unit. How easy was that!!!

Slid the shelf in place!

I removed the ice container found the part # on the bottom ordered a new one and installed it. It just slipped right in to place.

I took the side cover off. With a Phillips unscrewed the screw, took the outer part off, with nut driver undid the two screws. Took the part out in screwed the 4 Phillips head screws. Took out the broken part, replaced with new part. Reassembled. Put filter in and it now works perfectly.

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

The repair was easy. It just required a little time and patience. There are about a half dozen screws to remove and three of them are very small. I woild suggest a phillips head screwdriver with a magnetic tip for the small screws. They can easly fall into the control unit and be hidden. If they happen to fall, a small pen-type magnet that is expandable will make it easy to retrieve. I used a small set of needle-nose pliers to replace the small metal plates over the plastic pins that hold the water actuator in place. If your are careful, this repair can be done without disconnecting any of the electrical wiring.

Looked at video on how to remove and reinstall support and followed the instruct ions