The Lower Spray Arm is used in your dishwasher to spray water and clean your dishes. If broken there will be visible damage or your dishes may no longer be cleaned properly. If your spray arm is broke...
$45.60
In Stock
Order within the next 10 hrs and your part ships today!
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
$47.19
In Stock
Order within the next 10 hrs and your part ships today!
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
$8.76
In Stock
Order within the next 10 hrs and your part ships today!
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and ...
$41.19
In Stock
Order within the next 10 hrs and your part ships today!
This plastic cover and stem assembly helps hold the lower spray arm in place.
$39.53
In Stock
Order within the next 10 hrs and your part ships today!
Questions And Answers for FFCD2413US2A
Ask our experts a question about this model and we'll get back to you as soon as possible!
17 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Terry
September 17, 2021
Heavy soap residue left on dishes, silverware and inside of door
For model number FFCD2413US2A
Hello Terry, Thank you for your inquiry. We have researched the model you have provided and we would recommend checking the following parts to fix your issue: the heating element, the lower spray arm, the center spray arm, the motor and pump assembly, and the dishwasher filter. You can check the spray arms for any damages or clogs, make sure your filter is clean, and test the element the motor and pump assembly with a multimeter to see if they have continuity. Good luck with your repair.
Originally my washer would not fill with water, after replacing the water inlet valve it now fills, but when the pump is supposed to start and send water to the sprayer arms, i just hear a low rumbling noise coming from under the washer and nothing else happens. I am between buying a new controller board or a motor? Any advice would be greatly appreciated
For model number FFCD2413US2A
Hello Jarrod, all the spray arms there is mostly likely an issue with the pump motor part PS12712308. Also check that the filter is not clogged or the spray arms are blocked. The center spray arm is PS11770527. The lower spray arm PS12585623. Thank you for your question and good luck with your repair!
Runs through cycle but does not clean dishes. Tablet just lays on bottom
For model number FFCD2413US2A
Hello Lori, Thank you for writing. It likely is that the water is not hot enough. The normal water temperature for dishwasher tablets to dissolve is 120-160ºF. This is the way you can tell if the water isn't getting hot enough to dissolve the tablet.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Abraham
September 1, 2021
Will fill with water but runs out, will not hold in the basin.
For model number FFCD2413US2A
Hello Abraham, Thank you for the question. If the water is draining as it fills, we suggest testing the Float Switch and the Float. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Door would not latch, fixed that. Now the discharge pump will not shut off so it can start a cycle
For model number FFCD2413US2A
Hello William, Thank you for your inquiry. We would recommend checking the water inlet valve and the float switch. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you.
I have had to keep replacing the spray arm on the bottom of my dishwasher which takes like 2 seconds to do.. First you open the dishwasher and than pull the bottom basked forward and reach down and pull the spray arm up and pop the bottom of the spray arm off and put it on the new spray arm and slip it back into the dishwasher over the thing that makes it spin around.. but the tricky part is and I didn't know this and this is why my dishwasher spray arm kept falling over and melting on the heating element.. you have to turn it till it clicks in.. and your done..
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.
