FEP310BW0 Roper Range - Instructions

1. Turn off circuit breaker, pull out element and remove reflector pan.
2. Unfasten terminal block mounting screw and remove terminal block from casing.
3. Cut wires as close to defective terminal block as possible (not as per instructions) since you will need the maximum possible length of wire.
4. Slip on heat shrink sleeves, strip stove wires and connect to new terminal block per instructions.
5. Heat shrink sleeves per instructions.

Removed 2 screws holding element in place. Pulled out element to access two wires. Slid off the old element connectors. Placed new element in place and attached the two wires. Pushed it back into place and replaced the screws. Done in 10 min max.

simply turned off power. took old element out, held in by two screws. pulled out far enough to take off wires. removed and replaced with new element. that was a purfect fit. Works great.

I just had to pull out the old burner and straighten the prongs for the new burner and insert, The prongs of the new burner were slightly bent in shipment, but were easy to straighten with the pliers. The burners were sent in a bag and not a box -- therefore the prongs were easily bent. I was very pleased that I (73 year old lady) was able to fix my stove without a repairman. Saved $$$

Simple, just pull out old burners and slide new ones in place. Tried both, they work excellent!

SUPER EASY! The part arrived very quickly. I turned off the circuit breaker, unscrewed the few nuts, pulled out the element and reversed the process. 'works beautifully! Thanks so much.

took out the old heating elments and cleaned the bottom & top of oven with out the elments in, which made it alot easier then put new ones in. They were very easy to do, just make sure you watch how you took old ones out and don't loose the screws cause you use them to put new ones in.

removed old Plug-in block by removing 1 screw and cutting 2 wires. (Screw was so tight and rusty that I had to use vise grips to remove it). Installed new Plug-in block with wire nuts and heat shrink wraps. YOU just have to make sure the wires are seated in the block properly. This job was much easier than I anticipated. The burner works great now!

Not only it was easy to install but to find them was even quicker, thanks to Part Select.com. After searching for quite some time I found the site and my problem was solved. Item was received in a timely manner and replacing was very quick.
Thank you.

Unplugged old burner elements. Popped in new burners. Turned on the burners to test.

Replaced with the new burner works like new. Thanks a bunch!

The broiler unit had disintegrated at both connections. I removed the two screws in the top of the oven holder the unit, pulled out the unit, measured and ordered a replacement.

To replace the element, I pulled out the stove, removed the rear panel, located the connections for the broiler unit, remove parts of the old unit. I then attached the new unit to the top of the oven with the two screws, went around back and pushed in the two connections, replaced the back cover and replace the stove. It took about 30 minutes because I cleaned everything and sprayed bug spay (another plus for doing the repair myself).

grandson removed the two screws holding in the burned out unit and removed the two wires, installed them into the new unit and put the prongs into place. very easy and certainly very economic. delivery was quick and postage was reasonable. Thank you.

I removed surface burner and drip pan from stove. Then drilled out the remaining part of the old stabilizer clip. Once clip was removed I installed the new stabilizer clip with the screw and nut that came with the clip. Then I placed the drip pan back into position and installed the burner and locked it into the new clip.

I had to remove the original clips (broken or damaged). This was the hardest part -- the clips were held on by rivets (not screws), so I had to pound/punch them out (using care so not to damage the stove top). Once I punched the rivet out all that remained was a small hole, I just used the small nut and bolt that came with my stablizer clip kit and mounted the new clips. Everything worked out fine.