F14F2CDYP4 LG Washer - Instructions

It was so easy. i searched my model it brought up this site and the most common problem popped up without my even asking and recommended the part. i got it one week later and it was so simple to fix. a repair man wanted three times the part price to come to my home twice and would have had to wait longer. you guys were very helpful

new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.

I received the part needed within a few days from ordering. I immediately removed the leaking part with the new part. It was a very simple install, and my washer is now leak free. If you think you cannot do these simple changes, think again, it's much easier then you may think. Remove the top cover of your washer machine by taking off the two screws in the back. Remove the hose clamp with a pair of pliers and pull off from the intake valve, of course make sure your water valve is shut off before starting. Remove the two prong clip. Using your pliers, disconnect the main hot water hose. Use a Phillips screwdriver to remove the two screws that holds the valve in place. Remove and discard it and replace with the new valve. Follow the steps and your done, it's that easy....TC

UNPLUG WASHER.Unscrew 4 screws holding silver plate at back of unit. Remove plate to expose inside of unit. Locate drain hose at bottom of washer tub. Hose connects at front drain, bottom of tub, and at rear at the pressure sensor. Front and rear simply slide clamps down by grasping clamp tabs and sliding clamp off connection point. Disconnect from tub bottom by loosening main clamp with Phillips screwdriver and pulling downward. Have a towel handy as there will be water in the hose, and it will pour out when removing it from the unit. Installation is the reverse of removal. ATTACH THE HOSE ASSEMBLY TO THE DRUM FIRST, THEN FRONT, THEN LASTLY REAR. This order is the easiest way, otherwise you will spend extra minutes trying to get the tub connection to seat properly. Plug it back in (duh), then you're good to go for another 4 years or so until another hole wears in the hose. I have performed this repair on 3 different units, with 4 years being the average lifespan of this part.

Followed the instructions that a fellow DIYer posted in PartSelect and a few I watched on Youtube. Pull out the detergent drawer, remove the back screws, slide the top off, unclip the control board, unplug Power & One more switch so that I could move it aside. Take the gasket retention wire off the door gasket & tuck it inside. Remove the screws in the bottom & top. Then slide the front panel, including the door up (not easy) and out. The part received was only the pump motor so I had to take a few pictures before so I knew I got it together right. Remove drain houses, pump screws, slide pump back and remove pump. A few more screws to remove the pump from the housing & replace with new pump. Put it all back together. It works! It only took about 45 minutes

We drained the water from the washer via the tiny hose/filter located at the lower left corner of the washing machine. The unit was then pulled away from the wall, unplugged and the hoses disconnected. At this time, we used the wet dry vacuum to suction the water that remained in the drain hose. We tilted the washing machine back until the front of the unit was 18 inches or so off the floor. We used the foot stool to hold the washer up in the air so that we could work on the pump. Replacing the pump was as easy as removing a few screws, unplugging the electrical connections and removing the faulty pump assembly from the plastic housing. (Be sure to mark what connector goes in what terminal). Re-assemble. Re-connect. You are ready to go. It took more time to ready the washer than it did to replace the part.

ordered part from Part Select and it was here very quickly,but the part came damaged (not the fault of Part Select). I ordered another one and PartSelect had it here the next day. I watched the video on how to replace it and it was very helpfull.The particular part I replaced (pump motor) does not seem very durable. I will buy an American made washer the next time I need one. I will use Partselect in the future and recomend it to others.

Tipped the washer on its side to expose the bottom, removed the plastic lid adjacent to the pump after removing the screws holding it , then, using a flat head on a pry tab pulled out the pump, removed the hoses with pliers to complete the extraction, swapped the pump on my bench. . assembly is reverse of disassembly. .

The pump is apparently used for more than one washer, and the R&R instructions may be significantly different. I found a youtube video for my exact washer.

Removed the top, the front, got to the pump, removed it and replace it with the new one.

Found the part of Part Select by describing the problem. used a Utube video and step by step we were able to take apart, replace and put back everything with just a screw driver - I saved so much money!

Found on line OE meant washer not pumping out water with the suggestion to clean the filter and inspect the pump and lines for blockage. No problems there. You must be careful to empty the water manually before removing the filter. My wet vac helped but I still made a mess. I found a mechanic to look at the washer. He said it is common for the pump on these washers to go bad, especially if the washer has sat out of service. They wanted $300 to replace the pump. I found the part on this website for $53 and replaced it myself. The only hard part was emptying the water without making a mess and leaning the washer up and back far enough safely to remove the pump, then working on my back under the machine.

My washer would try to spin and remove the water according to the time allowed. Consequently my washer would take longer than the time allowed to drain therefore water would send a code error then the machine would stop working. So I remove the hose from the pump and found my son's little small sock blocking the drain. I removed the sock and reinstalled all hoses. Everything is fine now. No need for a replacement item. Just a little servicing.

greate very easy and the parts fit awsome the shiping was fast and easy very satified

Contacted LG customer service, not much help there. Watched a very helpful Utube video on how to find and repair the leak. The video suggested that the most common leak is in the drain hose with bellows. Removed the rear panel and removed the bellows unit using pliers for the clamps and screwdriver for the bellows part. This was pretty easy. The rubber bellows was leaking in the exact same place as the youtube video showed. This is a Design Flaw that LG needs to fix. Ordered the new part and installed the bellows portion of the part first, as the angle for that installation needs to be correct. Then attempted to install the end of the hose (very inaccesible) to the pump drain. Very difficult to position the factory supplied spring clamp with pliers so I purchased a screw-type clamp (using the nut-driver rather than a screw-driver to tighten the clamp was helpful) at the local hardware store and that made my job much easier. Note: My unit is mounted on a pedestal, so it was a little easier to access the part location (about one foot off the floor, rather than at floor level), but it may be that the part should be replaced from the bottom of the unit, which would make it much easier to access. Then I installed the other end of the hose to the drain line using a screw-type clamp. I am 69 years old, and not that flexible anymore, so getting down on the floor to reach inside the unit was difficult. You need patience to do this job and you have to make sure all the clamps are properly installed so you don't start the machine up and end up with another leak. For me, this process was difficult and took more than two hours to complete. Limited access to the area made it more difficult and I hate the factory clamps they use. Overall, the repair costs about $25, compared to the $125 just to come look at the machine, then more money to fix the unit. It was satisfying to complete the repair for a small amount of money, but not sure it was worth the aggravation.