F12A4FNP9 LG Washer - Instructions

Contacted LG customer service, not much help there. Watched a very helpful Utube video on how to find and repair the leak. The video suggested that the most common leak is in the drain hose with bellows. Removed the rear panel and removed the bellows unit using pliers for the clamps and screwdriver for the bellows part. This was pretty easy. The rubber bellows was leaking in the exact same place as the youtube video showed. This is a Design Flaw that LG needs to fix. Ordered the new part and installed the bellows portion of the part first, as the angle for that installation needs to be correct. Then attempted to install the end of the hose (very inaccesible) to the pump drain. Very difficult to position the factory supplied spring clamp with pliers so I purchased a screw-type clamp (using the nut-driver rather than a screw-driver to tighten the clamp was helpful) at the local hardware store and that made my job much easier. Note: My unit is mounted on a pedestal, so it was a little easier to access the part location (about one foot off the floor, rather than at floor level), but it may be that the part should be replaced from the bottom of the unit, which would make it much easier to access. Then I installed the other end of the hose to the drain line using a screw-type clamp. I am 69 years old, and not that flexible anymore, so getting down on the floor to reach inside the unit was difficult. You need patience to do this job and you have to make sure all the clamps are properly installed so you don't start the machine up and end up with another leak. For me, this process was difficult and took more than two hours to complete. Limited access to the area made it more difficult and I hate the factory clamps they use. Overall, the repair costs about $25, compared to the $125 just to come look at the machine, then more money to fix the unit. It was satisfying to complete the repair for a small amount of money, but not sure it was worth the aggravation.

Followed the manufacturers instructions to disassemble the washer from the top. There was a video on youtube of a guy who was able to replace his bellows hose from the back, but maybe my arms weren't long enough, I couldn't reach all the way to the front. The washer was pretty easy to take apart, except for taking off the top, where there were 2 extra screws not mentioned in the instructions. Replacing the part was really easy. HERE'S THE MOST IMPORTANT PART: LG DOESN'T MENTION IT IS REALLY HARD TO GET THE CLAMP ASSEMBLY BACK ON THE GASKET WITHOUT A SPECIAL TOOL. You can buy the special LG tool, or you can do what I did (and others on the internet) and buy an $8 "Brake spring spreader" tool at your local auto parts store. Repair was a success. No more water leaking!

Used a screwdriver to carefull lift the top of washer. Reached in and unplugged old assembly from wir harness. Unscrewed old one (2 screws) from washer screwed in new one connected it to wire harness. Closed top of washer and plugged it in and it was ready to use. I am a 53 year old female and had never done this before. The repair shop wanted $150 to install part plus the part cost more from them. I' m sure a guy could do the job in 15 minutes or less.

I received the part needed within a few days from ordering. I immediately removed the leaking part with the new part. It was a very simple install, and my washer is now leak free. If you think you cannot do these simple changes, think again, it's much easier then you may think. Remove the top cover of your washer machine by taking off the two screws in the back. Remove the hose clamp with a pair of pliers and pull off from the intake valve, of course make sure your water valve is shut off before starting. Remove the two prong clip. Using your pliers, disconnect the main hot water hose. Use a Phillips screwdriver to remove the two screws that holds the valve in place. Remove and discard it and replace with the new valve. Follow the steps and your done, it's that easy....TC

My washer would try to spin and remove the water according to the time allowed. Consequently my washer would take longer than the time allowed to drain therefore water would send a code error then the machine would stop working. So I remove the hose from the pump and found my son's little small sock blocking the drain. I removed the sock and reinstalled all hoses. Everything is fine now. No need for a replacement item. Just a little servicing.

Found on line OE meant washer not pumping out water with the suggestion to clean the filter and inspect the pump and lines for blockage. No problems there. You must be careful to empty the water manually before removing the filter. My wet vac helped but I still made a mess. I found a mechanic to look at the washer. He said it is common for the pump on these washers to go bad, especially if the washer has sat out of service. They wanted $300 to replace the pump. I found the part on this website for $53 and replaced it myself. The only hard part was emptying the water without making a mess and leaning the washer up and back far enough safely to remove the pump, then working on my back under the machine.

The pump is apparently used for more than one washer, and the R&R instructions may be significantly different. I found a youtube video for my exact washer.

Removed the top, the front, got to the pump, removed it and replace it with the new one.

Found the part of Part Select by describing the problem. used a Utube video and step by step we were able to take apart, replace and put back everything with just a screw driver - I saved so much money!

Took off the old one and put the other one on. The only difficulty was that my husband has big hands and had a hard time getting to one end.

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

Turn off hot water supply and activate a cycle on the washer momentarily, with hot water selected on front panel options to relieve hose pressure. Slide washer out to gain access to rear of unit. Unplug washer from AC source. Using pliers, remove washer supply hose from washer-side of the line (water may drain from hose) Remove single Phillips screw at bottom of each nylon lid holder at rear. Using a plastic putty knife, place between front panel and top lid to loosen lid and slide to rear. Remove lid and store aside. Hot and cold inlet valves sit side-by-side at top rear of the unit. Disconnect connector from valve by pulling gently away from valve plug prongs and place to the side. Using pliers, compress hose clamp and move to lower section of hose. Carefully rotate hose back and forth to remove from assembly. Inlet valve is held to washer body rear with 3 small Phillips screws. Remove first 2 and then while holding inlet valve body, remove final screw to free inlet valve assembly. Replace with new assembly by reversing these steps.Make certain when supply hose is reconnected, it is firmly tightened but DO NOT over tighten. Test washer by running a cycle to ensure there are no leaks.

Hardest part was getting the correct part. Due to some glitch somewhere there was a mix up in the database for the correct pump number. This unit has two pumps mounted to the same housing. One is a recirculating pump and one is discharge pump. I ordered the discharge pump and kept receiving the recirculating pump. Discharge pump is LG PART#4681EA2001T and recirculating pump is LG PART #4681EA2002H Once in hand the install went fairly smoothly. Removed top - two screws on back of unit. Removed control panel with one screw on upper right inside corner, associated plugs and snap clips. Removed soap tray and drained water through filter tube. Removed screws in front of filter. Using Vise grips stretched spring from around front seal. Removed screws holding front of washer to top frame (2?)[accessed after soap tray removal]. Pump assembly located in bottom left, removed associated hoses, Marked wired colors on pump housings and removed. Removed assembly. Unscrewed pump, installed new pump and reversed procedure to reassemble. Struggled mostly with replacing spring around front seal. Stretch it as far apart as you can as you "roll" the spring in and then massage the seal to get the spring into correct position. Definitely a doable repair. Good Luck.

Did the repair entirely from the back.- 4 screws back cover comes off. Once you see the Bellows it is obvious what needs to come off and there are other videos on the net showing this. The main things I did differently were 1) Leaned the washer forward and placed 3 2x4 blocks of wood under each back leg. This allowed me to reach under the washer with one hand, and through the back with the other. You need both hands in there ! 2) Uninstalling is easy with just pliers. But on the way back in, I used a pair of Locking Pliers to keep the circular clamp squeezed as much as possible. That seemed the only way to get the bellows back in. Another option would be to switch to screw on Pipe clamps instead of the spring clamps.