F1298FYN LG Washer - Parts

The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small f...Read morelat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse order -- taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.

This hot water inlet valve is designed to regulate water flow into the washing machine during operation. Featuring a standard hose fitting inlet and a single water outlet, it opens as needed to allow hot water into the appliance. If the valve is defective, you may notice slow filling, no filling at all, or water leaks. A simple way to tes...Read moret the valve is to unplug the washer when the issue occurs—if water continues to flow, the valve is likely faulty and should be replaced. The part measures approximately 3 inches in length by 3 inches in width and is sold individually.

This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose connects the dispenser assembly to the tub. Before beginning the repair, unplug the washer and turn off the water supply. You will need a Phillip...Read mores head screwdriver to complete this repair; a clamp tool can also be helpful. Remove the screws holding the lid of the washer in place, and take off the lid. Locate the dispenser hose and remove its clamps. Place the clamps on the new hose, using the arrows for a guide in positioning the clamps. Install the new hose and reassemble all other parts.

This washer sensor assembly, also known as a motor rotor position sensor, is a genuine OEM replacement part designed to monitor the direction and speed of the rotor during operation. By communicating this data to the electronic control board, it ensures proper spin and agitation cycles. A malfunctioning sensor may result in the washer pum...Read moreping but failing to spin or agitate, leading to incomplete wash cycles. This part is sold individually and is compatible with select washer models. For safety, always disconnect power before beginning installation, and verify model compatibility prior to purchase.

The magnetic door plunger attaches to the inner door panel of your washer and will hold the door open when the washer is not in use and allows the door and tub seal to dry. By doing this it will prevent mold and mildew buildup around your door and seal. If your washer door will not close you many need to replace this part. The magnetic door plunger is a genuine OEM part.

This kit includes 1 shock absorber and 2 pins.

This door lock assembly is a critical component in compatible washing machines, responsible for confirming that the door is securely closed before initiating a wash cycle. When functioning properly, it communicates with the control system to engage the locking mechanism. A faulty switch may prevent the door from latching, opening, or star...Read moreting the cycle. Located behind the front panel, replacement requires removal of the door gasket and access to the internal housing. Sold individually.

This hose has bellows to allow for flexibility during the wash and spin cycles.

This round rubber tub seal is designed to prevent water leakage between the front and rear halves of the outer tub in select washing machines. Positioned at the junction of the tub components, it compresses during operation to maintain a watertight seal, ensuring efficient washing performance and protecting internal components from moistu...Read morere damage. A worn or damaged seal may result in water leaks, unusual operational noises, or reduced washing effectiveness. Replacing the seal restores proper containment and supports the overall functionality and longevity of the appliance. Installation may require partial disassembly of the tub assembly.

The blue plastic detergent dispenser holds the detergent and then dispenses it into the washer during the wash cycle. If the detergent dispenser is broken, lost, or if the detergent is not dispensed during the wash cycle, you may need to replace it. The dispenser is approximately 4-inches wide, 4.5-inches long, 2-inches tall and is a genuine OEM part.